NautemyCoC orals · exams · job testsEarly access
Oral topic25 min readJump to 35 questions

Fuel oil purifier oral exam questions and model answers for marine engineers

Fuel oil purifier oral questions test centrifugal separation: Stokes' law, heating, choosing the gravity disc (heavier oil, smaller hole), the water seal, what to do when oil overflows and how to stop a purifier fire. Here are 35 model answers.

On this page
  1. Key facts
  2. What do examiners ask about fuel oil purifiers at each rank?
  3. How does a centrifugal purifier separate water and dirt from fuel?
  4. What is the difference between a purifier and a clarifier?
  5. How do you choose the gravity disc?
  6. How should you structure a purifier answer in the oral?
  7. What mistakes do candidates make on purifier questions?
  8. What purifier emergencies do examiners give you?
  9. Why is the purifier room a fire risk, and what protects it?
  10. What changes in purification with low sulphur fuels?
  11. How do you fault-find a purifier step by step?
  12. How do strong and weak purifier answers compare?
  13. What should you read to revise purifiers?
  14. Which engine topics link to fuel treatment?
  15. 35 practice questions
  16. Frequently asked questions
  17. Sources

Key facts

Principle
Centrifugal separation, Stokes' law
Purifier removes
Water and solids (two outlets)
Clarifier removes
Solids only (one outlet)
Gravity disc rule
Heavier oil, smaller hole
Fuel flash point
Not below 60 °C[1]
UMS rule
Overflow protection, separate space where practicable[2]
Asked in
MEO Class 4, 2, 1; MCA EOOW, Second and Chief Engineer
Questions here
35, core to trap

Checked 14 November 2026. Fees and rules change: confirm with the authority before you book.

What do examiners ask about fuel oil purifiers at each rank?

Purifier questions test whether you understand centrifugal separation well enough to set it up, fault-find it and stop it causing a fire. Operational-level candidates[3] must explain the gravity disc, water seal and sludge discharge and handle an overflow. Management-level candidates[3] must also plan fuel treatment for difficult fuels, cat fines and changeovers, and manage the fire risk of hot oil.

Purifiers are part of the marine engineering function for every engineer certificate[4] and sit in the MCA engineering oral syllabus[5]. Expect them in the MEO Class 4 oral, MEO Class 2 oral, MEO Class 1 oral, the MCA EOOW oral, Second Engineer oral and Chief Engineer oral. The table is our reading of the syllabus depth, not a published marking guide.

Purifier questions by rank (our summary)
ExamWhat the examiner checksTypical questions
India MEO Class 4Principle and safe operationPurifier vs clarifier, gravity disc selection, water seal, starting and stopping, overflow action
India MEO Class 2Fault-finding and maintenanceBowl not closing, vibration, sludge discharge failure, bowl overhaul, cat fines
India MEO Class 1Fuel management decisionsTreating an off-spec bunker, cat fine damage on the main engine, purifier room fire, fuel changeover planning
MCA EOOWRoutine and non-routine operation on watchStart-up sequence, alarms, oil in the sludge tank
MCA Second EngineerMaintenance planning and system designSeries vs parallel operation, heater control, separation efficiency
MCA Chief EngineerResponsibility for fuel quality and fire safetyFuel analysis results, bunker disputes, local application fire-fighting, risk assessment

How does a centrifugal purifier separate water and dirt from fuel?

A purifier spins the oil so fast that the centrifugal force is thousands of times stronger than gravity. Heavier water and solids move outward to the bowl wall, light oil moves inward to the oil outlet. The separation follows Stokes' law: it is faster when the density difference is bigger, the particle is bigger and the oil viscosity is lower.

That is why we heat the fuel. Heating lowers viscosity much more than it lowers density difference, so separation improves. It is also why we reduce throughput for poor fuel: the oil stays in the bowl longer, so smaller particles have time to reach the wall. The table summarises what each variable does.

Stokes' law in practice
VariableEffect on separationWhat you control on board
Density difference (water minus oil)Bigger difference, faster separationHeat the oil; very dense fuels need a clarifier-type or self-adjusting separator
Particle sizeBigger particles separate much faster (square of diameter)Settling tanks first; reduced flow for fine particles such as cat fines
ViscosityLower viscosity, faster separationHeater outlet temperature as the maker recommends
Centrifugal force (speed and radius)Higher force, faster separationCorrect bowl speed; check for slipping friction clutch or brake on
Residence time (throughput)Lower feed rate, better separationFeed pump or flow control set to the needed rate, not maximum

What is the difference between a purifier and a clarifier?

A purifier separates two liquids (oil and water) plus solids, so it has two outlets and needs a water seal and a gravity disc. A clarifier separates only solids (and small amounts of water) from oil, so it has one liquid outlet and no gravity disc; the bowl is closed at the water outlet.

On many ships with older plant, a purifier and clarifier run in series for heavy fuel. Many modern installations use self-adjusting separators that have no gravity disc: a water transducer or sensor in the clean oil outlet detects when water reaches the disc stack and triggers a discharge or drains water through a valve. Name the principle, not the brand, in the oral.

Purifier, clarifier and self-adjusting separator
FeaturePurifierClarifierSelf-adjusting separator
RemovesWater and solidsSolids (little water)Water and solids
Liquid outletsTwo: oil and waterOne: oilOne oil outlet; water drained by valve or discharge
Gravity discYes, chosen for oil densityNoNo
Water seal neededYes, before feedNoNo conventional seal; displacement water used at discharge
Density limitLimited by gravity disc rangeNot limited by interfaceDesigned for high density fuels
Main riskBroken seal, oil overflowBowl filling with waterSensor fault, wrong settings

How do you choose the gravity disc?

Choose the gravity disc from the maker's chart using the oil density at the separating temperature. The disc sets the radius of the water outlet and so the position of the oil-water interface. The interface should sit just outside the disc stack.

Remember the direction. If the disc hole is too large, the interface moves outward, the water seal can break and oil escapes through the water outlet. If the hole is too small, the interface moves inward into the disc stack, water and dirt are carried into the clean oil, and separation is poor. The rule of thumb is: the heavier the oil, the smaller the gravity disc hole. The ideal disc is the one with the largest hole that still holds the seal. If the chart puts you between two sizes, follow the maker's instruction for that case and prove the choice by checking the water outlet for oil after start-up.

How should you structure a purifier answer in the oral?

Lead with the safety point, then the principle, then the procedure. For an overflow question the first thing to say is that hot oil is escaping and must be stopped: shut the feed, stop the purifier if needed, check the sludge tank. Then explain likely causes in order of how often they happen.

For procedure questions (start, stop, bowl cleaning) give the steps in sequence and give the reason for each. Examiners often interrupt with "why?"; if you have already given the reason, the question moves on. Rehearse answers aloud with the mock oral drill and check the numbers in the pumps and purifiers MCQ bank.

What mistakes do candidates make on purifier questions?

The biggest error is getting the gravity disc direction wrong. Say it carefully: bigger hole, interface outward, risk of seal loss and oil in the water outlet.

Other frequent mistakes:

  • Saying the purifier "removes cat fines completely". It reduces them; settling, correct temperature, low flow and good tank management all matter.
  • Forgetting the sealing water before opening the feed in a conventional purifier.
  • Confusing operating water (closes and opens the sliding bowl bottom) with sealing or displacement water.
  • Ignoring the fire risk. Hot fuel leaks onto a heater or exhaust are a classic engine room fire start; link your answer to fire-fighting.
  • Opening the bowl before it has stopped. The brake must be off only when running; the bowl must be at rest before you lift the cover.
  • Quoting one maker's temperatures as a rule. Say "as the maker recommends" unless you name the separator and manual.

What purifier emergencies do examiners give you?

The common scenarios are oil overflowing from the water outlet or into the sludge tank, the bowl failing to close after a sludge discharge, heavy vibration, and a fire in the purifier room. The steps below are the overflow drill.

  1. 1
    Stop the feed

    Shut the feed to the purifier (three-way valve to recirculation) so no more hot oil goes to the bowl.

  2. 2
    Check where the oil is going

    Look at the water outlet sight glass and the sludge tank level. Watch for oil spray or leaks near hot surfaces.

  3. 3
    Try a re-seal or a discharge

    If the seal was lost, supply sealing water again or make a sludge discharge to close the bowl properly, as the manual allows.

  4. 4
    Stop the purifier if it will not hold

    If the bowl will not close or overflow continues, stop it, apply the brake if fitted and allowed, and change over to the standby purifier.

  5. 5
    Find the cause

    Check operating water pressure, sliding bowl seal ring, gravity disc size, feed temperature and rate, back pressure on the oil outlet, bowl speed.

  6. 6
    Protect the service tank

    Make sure the daily service tank level is safe for the main and auxiliary engines while you repair.

  7. 7
    Record

    Log the event and the sludge tank level change; sludge tank contents are recorded in the Oil Record Book under MARPOL Annex I.

Why is the purifier room a fire risk, and what protects it?

Purifiers handle oil heated above its normal storage temperature, under pressure, next to electric heaters and motors. A leak or a split pipe can spray oil onto a hot surface. SOLAS requires oil fuel for machinery to have a flash point of not less than 60 °C[1], but heavy fuel in the purifier heater may be heated close to or above it, so leaks matter.

On ships with periodically unattended machinery spaces, purifiers need arrangements to prevent overflow and spillage and, where practicable, a separate space for the purifiers and their heaters, and heated tanks need a high temperature alarm where the flash point can be exceeded[2]. Many machinery spaces also have a fixed local application water system covering purifiers for heated fuel (SOLAS Ch. II-2 Reg. 10.5.6). Know where your remote stops and quick-closing valves are, as explained in fire-fighting and UMS and automation.

What changes in purification with low sulphur fuels?

Since the 0.50% global sulphur limit came in on 1 January 2020[6], many ships burn very low sulphur fuel oils (VLSFO) that are blends. They vary a lot from bunker to bunker in density, viscosity and cat fine content, and some are less stable. For the purifier this means three things.

First, re-check the gravity disc or separator settings for every new bunker, because density can change. Second, set the separating temperature for the actual viscosity, not the habit from the previous fuel; a low-viscosity blend needs less heat, and overheating low-viscosity fuel can cause gassing and unstable flow. Third, watch for sludge: if two fuels are incompatible, asphaltenes can drop out as heavy sludge, choking filters and filling the bowl quickly. The practical answer is to keep fuels segregated, test compatibility before mixing, shorten the discharge interval for the first hours on a new fuel, and watch filter differential pressures.

When changing over to 0.10% fuel before entering an emission control area, the purifiers may run on two different fuels in sequence. Flush lines through correctly and record the changeover as the rules require; see fuel sulphur rules and scrubbers.

How do you fault-find a purifier step by step?

Stop the oil loss first, then find the cause: shut the feed, check the sludge tank, then work through water seal, gravity disc and operating water. These walk-throughs follow the order an examiner expects.

Walk-through 1: oil coming out of the water outlet

Symptom. The sight glass on the heavy phase (water) outlet shows oil; the sludge tank level is rising.

Checks in order.

  1. Shut the feed so you stop losing oil. Check the sludge tank level against its high level alarm.
  2. Was the sealing water added before the feed was opened? Without a water seal, oil passes straight to the water outlet.
  3. Is the separating temperature right for the oil? Too low a temperature raises viscosity and density and pushes the interface outward.
  4. Is the gravity disc right for this bunker's density? A new bunker with a higher density than the last one needs a disc with a smaller hole; if the old, larger-hole disc stays in, the interface moves outward and the seal can break.
  5. Is the feed rate too high, or the back pressure on the clean oil outlet too high?
  6. Is the bowl fully closed? Leaking operating water or worn seals let oil escape.

Likely cause. Lost water seal, wrong disc after a bunker change, low temperature or excess back pressure.

Action. Correct the cause, re-establish the seal, restart and check the outlet before leaving. If the sludge tank is near full, stop and arrange transfer or disposal as the oily water separator page explains, and record it in the Oil Record Book.

Report. Log the event; tell the second engineer.

Examiner's note: The weak answer is "change the gravity disc". Panels want the seal, temperature and back pressure checks first, because they are faster and more often the cause.

Walk-through 2: the bowl will not close after a desludge

Symptom. After a sludge discharge, oil keeps flowing to the sludge outlet; the bowl does not close.

Checks in order.

  1. Shut the feed.
  2. Operating water pressure and supply: is the tank empty, the solenoid failed or the strainer choked?
  3. Bowl speed: if the motor current and speed are low (belt or friction coupling slipping), the bowl cannot hold closed.
  4. Dirt or a damaged seal ring on the sliding bowl bottom; the bowl needs opening and cleaning.

Likely cause. Operating water failure, low speed or a dirty or damaged sealing face.

Action. Stop the purifier, wait until the bowl has stopped completely, then open, clean and change seals.

Report. Log; maintenance system entry.

Examiner's note: Candidates forget that you only open the bowl once it has fully stopped, with the brake applied as the maker says.

Walk-through 3: heavy vibration on start-up

Symptom. The purifier vibrates heavily as it runs up, or later in service.

Checks in order.

  1. Stop it at once and keep clear.
  2. On start-up: was the bowl assembled correctly, with matching marks aligned and the lock ring tight?
  3. In service: uneven sludge build-up in the bowl, damaged disc stack, worn spindle bearings or buffer springs.

Likely cause. Wrong assembly or an unbalanced bowl.

Action. Do not restart until the cause is found. An unbalanced bowl at full speed can break up.

Report. Chief engineer and log.

Examiner's note: The strong answer starts with "stop it and keep clear", and names assembly marks.

How do strong and weak purifier answers compare?

Examiners mark the order and the reason. These are typical answers they hear.

Weak and strong answers on purifier questions
QuestionWeak answerStrong answer
Oil from the water outletChange the gravity disc.Shut the feed, check sludge tank, check seal water, temperature, back pressure, then disc against the new bunker density.
Why heat the fuel?To make it thin.Lower viscosity lets particles move faster to the bowl wall (Stokes' law), so separation improves.
Bigger disc hole means?Better separation.Interface moves outward; the seal may break and oil escapes through the water outlet.
Do purifiers remove cat fines?Yes, completely.They reduce them; settling, correct temperature, low throughput and tank management all matter.

What should you read to revise purifiers?

Read one textbook chapter for principle and your own separator's manual for settings:

  • Marine Auxiliary Machinery by H.D. McGeorge: centrifuges, gravity discs, fuel treatment systems.
  • Introduction to Marine Engineering by D.A. Taylor: fuel treatment and separators.
  • Reed's Vol 8 General Engineering Knowledge for Marine Engineers: exam-style coverage.
  • Pounder's Marine Diesel Engines and Gas Turbines: fuel quality, cat fines and engine damage.
  • The separator maker's instruction manual and your company fuel management procedure.
  • MARPOL Annex I Reg. 12 (sludge tanks) and Reg. 17 (Oil Record Book); see MARPOL and the oily water separator page.

Then practise with the main engine MCQ bank for fuel questions, read how to answer oral exam questions, and prepare the papers on the MMD exam documents checklist.

Oral practice

35 oral questions with model answers

Read the question, answer it out loud as if the examiner is across the table, then open the model answer and mark yourself honestly.

–0/35 done
  1. 1
    Core

    Explain the principle of a centrifugal purifier.

    Model answer points
    • Rotating bowl creates centrifugal force many times gravity.
    • Heavier water and solids move outward, lighter oil moves inward.
    • Separation rate follows Stokes' law: density difference, particle size squared, inversely viscosity.
    • Disc stack shortens the settling distance so separation is fast.
    • Clean oil leaves at the inner outlet; water at the outer outlet via the gravity disc; solids collect at the bowl wall for discharge.
    The examiner may follow up with
    • Why does heating improve separation?
    How did you do?
  2. 2
    Core

    What is the difference between a purifier and a clarifier?

    Model answer points
    • Purifier: oil-water separation plus solids, two outlets, gravity disc, water seal.
    • Clarifier: solids removal, one outlet, no gravity disc, water outlet blanked.
    • Clarifier gives better solids removal because there is no interface in the disc stack.
    • Series operation: purifier first, then clarifier, for heavy fuel on many ships.
    The examiner may follow up with
    • When would you run them in parallel?
    How did you do?
  3. 3
    Core

    How do you select a gravity disc and what happens if you choose wrongly?

    Model answer points
    • Use the maker's chart with oil density at separating temperature.
    • Gravity disc sets water outlet radius and so the interface position.
    • Interface should be just outside the disc stack.
    • Too large: interface moves outward, seal can break, oil out through water outlet.
    • Too small: interface moves inward, poor separation, water in clean oil.
    • Heavier oil, smaller hole. The best disc is the largest one that does not break the seal.
    The examiner may follow up with
    • Your fuel density has changed after bunkering. What do you check?
    How did you do?
  4. 4
    Core

    Walk me through starting a self-cleaning fuel oil purifier.

    Model answer points
    • Check oil level in the gearbox, brake off, bowl free to turn, correct gravity disc fitted.
    • Open operating water and check its pressure.
    • Start the heater circulation with the three-way valve on recirculation; heat to the set temperature.
    • Start the motor; wait until the bowl reaches full speed (current falls to running value).
    • Close the bowl with operating water, add sealing water until it shows at the water outlet.
    • Open feed slowly, check oil outlet back pressure, water outlet and sludge outlet for oil.
    • Set the discharge interval as the manual or fuel requires.
    The examiner may follow up with
    • Why do you wait for the current to drop?
    How did you do?
  5. 5
    Core

    What is the water seal and why is it needed?

    Model answer points
    • Water fed into the bowl of a purifier before the oil feed is opened.
    • It fills the outer (water) side up to the gravity disc so oil cannot escape through the water outlet.
    • The oil-water interface then forms just outside the disc stack, where the gravity disc puts it.
    • It is lost after a sludge discharge or if the bowl runs without feed; it must be restored before feed is opened again (automatic on most self-cleaning units).
    • Not needed in a clarifier, which has no water outlet.
    The examiner may follow up with
    • What happens if you open the feed before the seal is made?
    How did you do?
  6. 6
    Core

    How do you stop a purifier safely?

    Model answer points
    • Change the three-way valve to recirculation so feed to the bowl stops.
    • Displace oil with water if required, then make a final sludge discharge so the bowl stops clean.
    • Shut the heater (steam or electric) before or as the flow stops, so oil is not overheated in a stagnant heater.
    • Stop the motor; apply the brake only if the design allows.
    • Close operating water when stopped, as the maker says.
    • Do not open the bowl until it has stopped completely and the motor is locked out.
    The examiner may follow up with
    • Why shut the heater before stopping the flow?
    How did you do?
  7. 7
    Core

    What is operating water, sealing water and displacement water?

    Model answer points
    • Operating water: hydraulically moves the sliding bowl bottom to open the bowl (sludge discharge) and close it again.
    • Sealing water: forms the water seal in a purifier before feed.
    • Displacement water: pushes oil out of the bowl before a discharge to reduce oil lost to the sludge tank.
    • All need correct pressure and a clean supply; a blocked strainer or failed solenoid on operating water is a common cause of the bowl not closing.
    • Do not mix them up in the oral: operating water never touches the oil.
    The examiner may follow up with
    • What happens if operating water pressure is low?
    How did you do?
  8. 8
    CoreSOLAS Ch. II-2 Reg. 4.2.1 (flash point)

    Why do we heat the fuel before purification?

    Model answer points
    • Reduces viscosity sharply, so separation is faster.
    • Also increases the density difference slightly.
    • Temperature set by maker for the fuel grade.
    • Too high: water boils, unstable seal, possible flash point issues.
    • Steady temperature matters; a hunting heater upsets the interface.
    The examiner may follow up with
    • What happens if the heater temperature hunts?
    How did you do?
  9. 9
    CoreISO 8217 (fuel specification)

    What are cat fines and how does the purifier help remove them?

    Model answer points
    • Hard particles of aluminium and silicon oxides from catalytic cracking.
    • Cause severe abrasive wear of fuel pumps, injectors, liners and piston rings.
    • Removal: settling and service tank draining, correct temperature, low throughput.
    • Series or parallel operation as the maker advises.
    • Check fuel analysis on bunkering; sample before and after purifiers to measure efficiency.
    The examiner may follow up with
    • How would you notice cat fine damage on the engine?
    How did you do?
  10. 10
    Core

    Why do we have settling tanks before purifiers?

    Model answer points
    • Allow gravity separation of free water and heavier solids before the purifier.
    • Drain water and sludge regularly from the tank bottom, every watch.
    • Steady, controlled heating helps settling; avoid stirring the tank when filling.
    • Gives a buffer stock and time to test new fuel before it reaches the service tank.
    • Settling reduces the load on the purifier and helps cat fine removal.
    The examiner may follow up with
    • Why not fill the settling tank while drawing from it?
    How did you do?
  11. 11
    CoreSOLAS Ch. II-1 Reg. 47 (UMS fire precautions)

    What alarms and safety devices are fitted to a self-cleaning purifier?

    Model answer points
    • Low and high feed temperature, low feed pressure.
    • Water in oil or high water content (sensor-based systems).
    • Oil in water outlet / sludge overflow detection on many systems.
    • Low operating water pressure, discharge failure.
    • Vibration and motor overload; many have speed monitoring.
    • Overflow and spillage protection required on UMS ships.
    The examiner may follow up with
    • Which alarm would show a bowl that will not close?
    How did you do?
  12. 12
    CoreMARPOL Annex I Reg. 17

    Oil is coming out of the water outlet. What do you do?

    Model answer points
    • Stop the feed at once (three-way valve to recirculation).
    • Re-establish the seal or make a discharge to close the bowl.
    • Check gravity disc, operating water pressure, sliding bowl seal ring.
    • Check feed temperature and rate, outlet back pressure, bowl speed.
    • If it continues, stop and change over to standby.
    • Record sludge tank change in the Oil Record Book.
    The examiner may follow up with
    • How do you find out if the bowl is not closing?
    How did you do?
  13. 13
    Core

    How is a lube oil purifier operated differently from a fuel oil purifier?

    Model answer points
    • It runs continuously on the main engine sump (bypass purification), at a reduced flow to give a long residence time.
    • Separating temperature is usually lower than for heavy fuel, as the maker sets.
    • A larger gravity disc is used because lube oil is lighter than heavy fuel.
    • Water washing is not used on detergent (additive) oils because it removes the additives; follow the oil supplier's advice.
    • Watch for water in the sludge or water outlet: it points to a cooler or jacket leak.
    • Sample the sump oil regularly to check the purifier is keeping water and insolubles down.
    The examiner may follow up with
    • Why is water washing not used on detergent oils?
    • Where does the lube oil purifier take suction from?
    How did you do?
  14. 14
    Core

    What is the purpose of the disc stack?

    Model answer points
    • Divides the oil flow into thin layers between the discs.
    • Shortens the radial distance a particle must travel before it is separated.
    • Greatly increases the effective settling area of the bowl.
    • The distribution holes in the discs set where the feed enters, near the interface.
    • Damaged or dirty discs reduce efficiency and cause imbalance; clean them without scratching.
    The examiner may follow up with
    • Why must the discs be fitted in the right order?
    How did you do?
  15. 15
    Deeper

    The purifier bowl will not close after a sludge discharge. What could be wrong?

    Model answer points
    • Low operating water pressure or blocked strainer.
    • Worn or damaged seal ring on the sliding bowl bottom.
    • Sludge or hard deposits stopping the sliding bottom.
    • Faulty solenoid valve for opening or closing water.
    • Nozzles or channels in the operating water system blocked.
    • Action: stop, open and clean the bowl, renew seals.
    The examiner may follow up with
    • What is the operating water solenoid for?
    How did you do?
  16. 16
    Deeper

    The purifier vibrates heavily. What do you do and why?

    Model answer points
    • Stop the purifier and keep clear; do not apply brake hard unless the maker allows.
    • Likely causes: uneven sludge build-up, bowl parts wrongly assembled, damaged disc stack, worn bearings or spindle springs.
    • Wrong assembly marks on bowl parts cause imbalance.
    • After it stops, open and check; never restart until fixed.
    The examiner may follow up with
    • Why are bowl parts numbered or marked?
    How did you do?
  17. 17
    Deeper

    Describe a purifier bowl overhaul.

    Model answer points
    • Stop, isolate electrically, lock out, wait for the bowl to stop.
    • Use the maker's special tools; note reverse threads.
    • Remove cover, lock ring, disc stack; clean with suitable solvent, never use sharp tools on discs.
    • Inspect seals, sliding bottom, nozzles, distributor, erosion and corrosion.
    • Renew O-rings; check alignment marks on reassembly.
    • Check spindle height and gearbox oil.
    The examiner may follow up with
    • Why are some threads left-handed?
    How did you do?
  18. 18
    Deeper

    What is series operation and parallel operation of separators, and when do you use each?

    Model answer points
    • Series: purifier then clarifier, better solids removal and a back-up stage.
    • Parallel: two purifiers each at half flow, lower throughput each so better separation.
    • Choice depends on fuel quality and maker advice.
    • Cat fine-rich fuel often benefits from low flow per unit.
    The examiner may follow up with
    • Which arrangement suits cat fine-rich fuel?
    How did you do?
  19. 19
    Deeper

    How would you test purifier efficiency?

    Model answer points
    • Take fuel samples before and after the separator, and at the engine inlet.
    • Analyse water content and cat fines (aluminium plus silicon) at a laboratory.
    • Compare with the engine maker's limit for fuel at the engine inlet.
    • Check sludge quantity and bowl condition at cleaning.
    • Adjust temperature, throughput and discharge interval, then sample again.
    The examiner may follow up with
    • Where is the sampling point after the purifier?
    How did you do?
  20. 20
    Deeper

    What is the relationship between throughput and separation efficiency?

    Model answer points
    • Lower feed rate means longer residence time in the bowl.
    • Smaller particles then have time to reach the bowl wall (Stokes' law).
    • Run at the rate needed to keep the service tank full plus a small margin, not maximum.
    • Recirculate the surplus back to the settling tank rather than raising the feed to the bowl.
    • High rate for convenience is a common cause of cat fine damage.
    The examiner may follow up with
    • How do you set the throughput?
    How did you do?
  21. 21
    Deeper

    How does a self-adjusting high-density separator work without a gravity disc?

    Model answer points
    • Works as a clarifier with one oil outlet.
    • A water transducer or sensor in the clean oil outlet senses when separated water reaches the disc stack.
    • Control unit then opens a drain valve or triggers a sludge discharge.
    • Allows fuel densities beyond conventional purifier limits.
    • Faults: sensor fouling, wrong reference values.
    The examiner may follow up with
    • What happens if the water sensor fouls?
    How did you do?
  22. 22
    DeeperSOLAS Ch. II-2 Reg. 10.5.6 and Reg. 5

    A fire starts in the purifier room. What actions do you take?

    Model answer points
    • Raise the alarm, inform the bridge and chief engineer.
    • Stop purifiers and heaters from outside; shut quick-closing valves on the supply tanks.
    • Stop ventilation and close openings to the space.
    • Use the local application system or portable extinguishers if safe.
    • Boundary cool; prepare the fixed system if the fire spreads.
    • Account for all personnel.
    The examiner may follow up with
    • Why stop the fuel before fighting the fire?
    How did you do?
  23. 23
    Deeper

    How do you deal with water found in the service tank?

    Model answer points
    • Drain the service tank bottom until clean fuel; check settling tank drains too.
    • Check purifier settings, seal and water outlet; a lost seal or wrong disc passes water.
    • Check heating coils and steam leaks into the tank.
    • Check tank vents, sounding pipes and overflow lines for sea or rain water ingress.
    • Watch engine running for misfiring; change to the other service tank if needed and inform the chief engineer.
    The examiner may follow up with
    • How does water in fuel affect the engine?
    How did you do?
  24. 24
    Deeper

    How often should sludge be discharged?

    Model answer points
    • Interval set by fuel quality and maker advice.
    • Too long: bowl fills with sludge, separation falls, imbalance.
    • Too short: oil loss and wasted water.
    • Start with the maker's value and adjust by inspection of the bowl and sludge quantity.
    The examiner may follow up with
    • How do you decide on the interval for a new bunker?
    How did you do?
  25. 25
    DeeperSOLAS Ch. II-1 Reg. 47; SOLAS Ch. II-2 Reg. 10.5.6

    How do you prevent fire in the separator space under the rules?

    Model answer points
    • Overflow and spillage protection on separators.
    • Separators in a dedicated space with their heaters where practicable.
    • High temperature alarm on heated tanks where flash point may be exceeded.
    • Screening of fuel pipes and drip trays.
    • Local application fire-fighting in many machinery spaces.
    The examiner may follow up with
    • What is a local application system?
    How did you do?
  26. 26
    DeeperMARPOL Annex I Reg. 12 and Reg. 17

    Sludge tank level is rising faster than normal. What might be happening?

    Model answer points
    • Oil loss from purifier (overflow, broken seal, bowl not closing).
    • Too frequent discharges or poor displacement.
    • Leaking drains into the sludge tank.
    • Check each separator and record in the Oil Record Book.
    The examiner may follow up with
    • Which ORB code covers sludge?
    How did you do?
  27. 27
    Deeper

    How does the friction clutch on the purifier drive work and why is it fitted?

    Model answer points
    • Allows the motor to reach speed quickly while the heavy bowl accelerates slowly.
    • Friction pads slip during start-up, limiting motor current and time on starting current.
    • Starting current falls to running value when the bowl reaches full speed.
    • Worn or oily pads cause long start times and low bowl speed.
    • Low bowl speed reduces separation and can break the seal.
    The examiner may follow up with
    • How do you check bowl speed?
    How did you do?
  28. 28
    Trap

    Can you increase separation temperature to improve separation of a very viscous fuel without limit?

    Model answer points
    • No. Above about the boiling point of water the water in the bowl may boil and the seal becomes unstable.
    • Maker sets a maximum; do not exceed it.
    • Use lower throughput or a high-density separator instead.
    • Heater faults can overheat fuel and create fire risk.
    The examiner may follow up with
    • What is the usual maximum?
    How did you do?
  29. 29
    Trap

    Is a larger gravity disc better because it gives more separation?

    Model answer points
    • No. A larger hole moves the interface outward and risks breaking the seal.
    • Separation is best with the interface just outside the disc stack.
    • The right disc is the largest that still holds the seal for the oil density and temperature.
    • Use the chart; check the water outlet for oil after any change.
    The examiner may follow up with
    • What does a too-small disc cause?
    How did you do?
  30. 30
    TrapMARPOL Annex VI Reg. 18 (bunker delivery note)

    Your purifier has run fine for months. A new bunker arrives with higher density. Anything to change?

    Model answer points
    • Yes. Check the density at 15 °C on the bunker delivery note and the analysis.
    • Recheck the gravity disc against the chart for the new density.
    • Adjust temperature and throughput for viscosity and cat fines.
    • Avoid mixing incompatible fuels; do a compatibility test if needed.
    The examiner may follow up with
    • How do you do a compatibility test?
    How did you do?
  31. 31
    Trap

    The chief engineer asks you to bypass the purifier for a few hours to fill the service tank faster. Your view?

    Model answer points
    • Unpurified fuel can damage the engines (cat fines, water) within hours.
    • Suggest running both purifiers in parallel at moderate rate instead.
    • Find why the service tank is short: purifier trouble, high consumption, a leak.
    • Explain the risk; if the decision stands, record it and watch filters and engine closely.
    The examiner may follow up with
    • What engine damage can cat fines cause in hours?
    How did you do?
  32. 32
    Trap

    Can you open the purifier cover as soon as the motor stops?

    Model answer points
    • No. The bowl keeps spinning long after the motor is stopped.
    • Check the speed indicator or revolution counter shows zero.
    • Isolate and lock out the motor first.
    • Only then remove the cover, using the maker's tools.
    The examiner may follow up with
    • Why are bowl parts marked for position?
    How did you do?
  33. 33
    Trap

    Purifier water seal is lost and oil goes out of the water outlet. Why can this happen even with the right gravity disc?

    Model answer points
    • No sealing water after a discharge, or not enough of it.
    • Feed opened too fast, or feed rate too high for the bowl.
    • Feed temperature too high or fluctuating, or oil density higher than the disc allows.
    • Bowl not closed properly: low operating water pressure, worn sliding bowl seal ring or main seal, dirt on the sealing faces.
    • Back pressure on the clean oil outlet too high (valve closed, filter choked).
    • Low bowl speed from a slipping clutch or brake left on.
    • Act: feed to recirculation, re-seal or discharge, then find the cause.
    The examiner may follow up with
    • How would you prove the bowl is leaking?
    How did you do?
  34. 34
    TrapISO 8217

    A sample after the purifier shows high cat fines. The purifier seems to run normally. What next?

    Model answer points
    • Reduce throughput; check temperature is at maker's value.
    • Drain settling and service tanks more often.
    • Consider series or parallel operation.
    • Inform the chief engineer; check the bunker analysis and consider a protest to supplier.
    • Watch engine wear signs (fuel pump, injector, liner).
    The examiner may follow up with
    • What is the engine maker's cat fine limit at engine inlet?
    How did you do?
  35. 35
    Trap

    Do you need a water seal on a clarifier?

    Model answer points
    • No. A clarifier has no water outlet and no interface.
    • Feeding sealing water into a clarifier just fills the bowl with water.
    • Water collected in a clarifier is removed by sludge discharge, so discharge intervals matter.
    • Know which mode your machine is set for before starting it.
    The examiner may follow up with
    • What happens if a clarifier gets a lot of water?
    How did you do?

Reading answers is not the same as saying them. Our AI voice examiner asks these out loud, listens to your answer, asks the follow-up and marks you against the rule. Join early access or try the free timed mock oral drill.

Frequently asked questions

What is the difference between a purifier and a clarifier?

A purifier separates water and solids from oil and has two outlets, a gravity disc and a water seal. A clarifier removes solids only, has one oil outlet and no gravity disc. Many ships run them in series for heavy fuel.

How do you select a gravity disc?

From the maker's chart, using the oil density at the separating temperature. The heavier the oil, the smaller the disc hole. Too large a hole breaks the seal; too small gives poor separation.

Why is fuel heated before the purifier?

Heating lowers viscosity a lot, which speeds separation under Stokes' law. Use the temperature the maker recommends for the fuel grade; too high can cause boiling of water and unstable operation.

What causes a purifier to overflow?

Common causes are loss of water seal, a gravity disc that is too large, the bowl not closing (low operating water pressure or worn seal ring), feed rate too high, back pressure on the oil outlet and low bowl speed.

What is the water seal in a purifier?

A layer of water put into the bowl before the oil feed. It fills the water side so the oil cannot escape through the water outlet. It is lost if the bowl runs without water or after discharge without resealing.

What are cat fines and why do they matter?

Catalytic fines are small hard particles of aluminium and silicon compounds left from refinery cracking. They cause rapid wear of fuel pumps, injectors, liners and rings. Good settling, correct temperature and low throughput help the purifier remove them.

Why is throughput reduced for poor fuel?

A lower flow gives the oil more time in the bowl, so smaller particles reach the bowl wall. Running at maximum rate for convenience cuts separation efficiency.

What is operating water in a self-cleaning purifier?

Water that moves the sliding bowl bottom to close or open the bowl for sludge discharge. Low pressure or a blocked supply stops the bowl closing, which leads to overflow.

Why must the bowl stop fully before opening the purifier?

The bowl stores a lot of energy at speed. Opening it while it turns can cause serious injury. Lock out the motor and confirm the bowl has stopped before lifting the cover.

What is a self-adjusting separator?

A separator with no gravity disc. A sensor in the oil outlet detects water reaching the disc stack and starts a discharge or drains water. It can handle denser fuels than a conventional purifier.

Where does purifier sludge go and how is it recorded?

To the sludge tank required by MARPOL Annex I Reg. 12. It is later landed ashore or burnt in an approved incinerator, and each operation is recorded in the Oil Record Book Part I.

Is the purifier asked in MEO Class 4 orals?

Yes, it is one of the most common auxiliary machinery topics. Expect the principle, gravity disc, start-up, overflow and bowl cleaning questions.

Sources 6 documents

Each number in the text links to the source below. Labels show the type of source; see our editorial policy.

  1. Official Cayman Islands Shipping Registry CIGN 10-2023 Rev 01 Off-specification fuels (quoting SOLAS II-2/4.2.1) · 1 January 2023
  2. Official Isle of Man SD 603/98 Merchant Shipping (Cargo Ship Construction) Regulations 1998, Schedule 9 fire safety (SOLAS Ch. II-1 Reg. 47) · 1 January 1998
  3. Official STCW Code Section A-I/1 (as amended 2010) · 25 June 2010
  4. Official MSN 1857 (M+F) Amendment 1: UK requirements for engineer officers and engineer operators
  5. Official MIN 654 (M) Engineering and Electro-technical Officer Oral Exam Syllabus, Amendment 1 (April 2026) · 21 April 2026
  6. Official IMO: IMO 2020 – cutting sulphur oxide emissions

Where should you go next?

  • Oral topics14 pages: examiner questions with model answer points, deck and engine
  • Question banks7 pages: free MCQ sets with answers and explanations
  • CoC exam guides16 pages: every oral and written exam, authority by authority
  • Free tools4 pages: mock oral drill, lights trainer, sea-time calculator, practice tests
Exam Prep DeskMaritime exam researchers

We write from the conventions (STCW, COLREG, SOLAS, MARPOL), the authorities' own notices and published syllabi, and cite the source for every fee, rule and date. We are independent and not linked to any maritime administration or test provider. Found an error? It matters at sea: tell us and see how we correct · Disclaimer.

Related guides

AI voice mock oral

Say it out loud before the examiner asks.

Our examiner asks CoC oral questions by rank and function, listens to your answer, asks the follow-up and scores you against the rule. Early access is open for India first.

  • Deck and engine, every rank
  • Answers referenced to the conventions
  • Independent, not linked to any authority
WhatsApp us