NautemyCoC orals · exams · job testsEarly access
Question bank25 min readJump to 40 questions

Ship stability MCQ practice: 40 questions with calculations, explanations and IS Code criteria

These 40 free ship stability MCQs cover GM, KG after loading and discharging, free surface correction, list, TPC, FWA and DWA, trim with MCTC, and the IS Code 2008 and Grain Code criteria. Every calculation answer shows the working.

On this page
  1. Key facts
  2. How should you use this ship stability MCQ set?
  3. Ship stability in 10 rules and numbers
  4. What are the common traps in ship stability MCQs?
  5. How do you work the calculation questions?
  6. Which traps does this set use, and what is the rule?
  7. Revision table
  8. Where is ship stability examined?
  9. What should you study after this set?
  10. 40 practice questions
  11. Frequently asked questions
  12. Sources

Key facts

Questions
40 MCQs, 4 options each
Calculations
14 worked problems (KG, GM, FSC, list, TPC, FWA, DWA, trim)
Rules covered
IS Code 2008 Part A, International Grain Code, Load Lines 1966
IS Code 2008 in force
1 July 2010[1]
Levels
Core, deeper and trap questions
Best for
2nd mate, chief mate and master candidates; CES and company tests
Cost
Free, no sign-up

Checked 13 November 2026. Fees and rules change: confirm with the authority before you book.

How should you use this ship stability MCQ set?

Do the set once without notes, mark every question you guessed, then redo only the guesses after reading the explanations. Stability is the subject where a guess that happens to be right hides a real gap, so treat a lucky guess as a wrong answer.

For the calculation questions, work on paper with a calculator before you look at the options. In the written papers and in company tests, the wrong options are often the answers you get from a common slip: dividing by the old displacement instead of the new one, forgetting to cube the tank breadth, or using the TPC in fresh water. If your number matches an option, check that you did not make one of those slips.

The questions run from core (what every officer must know) through deeper (calculations and code criteria) to trap (the questions candidates most often get wrong). When you can score 36 or more out of 40 twice in a row, move on to explaining the same ideas aloud. Oral examiners ask you to draw the GZ curve, explain why the ship lolls, and talk through a list correction, and an MCQ score does not prove you can do that. Practise with the mock oral drill, take a timed mixed set in the practice test, and read the full examiner-style questions on our ship stability oral topic page. If you want an examiner that asks the questions out loud and follows up, join early access for our AI voice mock examiner.

Ship stability in 10 rules and numbers

These are the numbers and formulas that the questions below test most. The intact stability figures come from Part A of the 2008 Intact Stability Code, which took effect on 1 July 2010[1]. The grain figures come from the International Grain Code under SOLAS Chapter VI. See also the glossary entries for metacentric height and free surface effect.

Core stability formulas and criteria
ItemRule or numberSource
Metacentric heightGM = KM − KG; KM = KB + BM; BM = I ÷ VStability theory
New KG after loading or dischargingSum of moments about the keel ÷ new displacementStability theory
Free surface correctionFSC = FSM ÷ displacement; FSM of a rectangular tank = l × b³ ÷ 12 × density of the liquidStability theory
Shift of G and listGG1 = w × d ÷ Δ; tan list = GG1 ÷ GMStability theory
Sinkage and TPCSinkage (cm) = w ÷ TPC; TPC = A × 1.025 ÷ 100 in salt waterStability theory
Fresh water and dock water allowanceFWA (mm) = Δ ÷ (4 × TPC); DWA = FWA × (1025 − dock density) ÷ 25Load Lines 1966, Annex I
Change of trimTrim change (cm) = trimming moment ÷ MCTCStability theory
Area under the GZ curveAt least 0.055 m-rad to 30°, 0.09 m-rad to 40° (or flooding angle), 0.03 m-rad between 30° and 40°IS Code 2008 Part A 2.2.1
GZ and GM minimumsGZ at least 0.20 m at an angle of 30° or more; maximum GZ at 25° or more; initial GM at least 0.15 mIS Code 2008 Part A 2.2.2–2.2.4
Grain cargo criteriaHeel from grain shift not over 12°; residual area at least 0.075 m-rad; GM (fluid) at least 0.30 mInternational Grain Code A 7

What are the common traps in ship stability MCQs?

Most wrong answers in stability come from five habits. Check each one before you choose an option.

  1. Dividing by the wrong displacement. After loading or discharging, the new KG is the total moment divided by the NEW displacement. Using the old displacement gives a number that is close and usually appears as an option.
  2. Thinking free surface depends on how much liquid is in the tank. For a slack tank with a flat bottom and vertical sides, the free surface moment depends on the length, the breadth cubed and the density of the liquid. It does not depend on whether the tank is 20% or 80% full. It disappears only when the tank is pressed up or empty.
  3. Confusing list and loll. A list comes from G being off the centreline with positive GM. A loll comes from negative GM with G on the centreline, and the ship lies over to either side. The cure for a list is to move weight across. The cure for a loll is to lower G. Moving weight across a lolling ship can make her flop over to the other side with a larger angle.
  4. Forgetting where a suspended weight acts. The moment a heavy lift leaves the quay or the deck, its weight acts at the derrick head or crane jib head, not at its own centre. G rises before the lift has moved at all.
  5. Mixing up FWA and DWA. The FWA is for water of density 1.000 t/m³. In dock water of 1.010 t/m³ the ship sinks by less than the FWA, so the DWA is always smaller than the FWA.

A sixth trap is the IS Code numbers. Candidates swap 0.055 and 0.09, or remember 0.20 m as the minimum GM instead of the minimum GZ at 30°. Learn the table above as a set. For the oral, know where each number comes from; our ship stability oral questions show how examiners probe it.

How do you work the calculation questions?

Set every stability sum out as a table of weights, levers and moments, then divide once by the final displacement. Each example below was worked twice, once by moments and once by a quick check.

Example 1: final KG and fluid GM after a loading plan. Displacement 8,000 t, KG 7.20 m. Load 1,200 t at Kg 4.50 m and 600 t at Kg 9.00 m; discharge 300 t at Kg 2.00 m. KM at the final draught 7.95 m. Free surface moments of slack tanks total 950 t-m.

Item Weight (t) Kg (m) Moment (t-m)
Ship 8,000 7.20 57,600
Load +1,200 4.50 +5,400
Load +600 9.00 +5,400
Discharge −300 2.00 −600
Final 9,500 67,800
  1. KG = 67,800 ÷ 9,500 = 7.137 m. Dividing by the old 8,000 t gives 8.48 m, the trap in question 4.
  2. Solid GM = 7.95 − 7.137 = 0.813 m.
  3. FSC = 950 ÷ 9,500 = 0.100 m, so fluid GM = 0.713 m, above the IS Code minimum of 0.15 m (question 27).
  4. Check: discharging a low weight raised G and loading the high 600 t raised it too; the low 1,200 t pulled it down by more. A small net fall from 7.20 m is what the table should show.

Example 2: list while a heavy lift hangs from the derrick. Displacement before the lift 10,000 t, KG 7.00 m, KM 8.00 m (take it as unchanged). Lift 150 t off the quay with the derrick head 22 m above the keel and 14 m out from the centreline.

  1. The weight acts at the derrick head as soon as it leaves the quay (question 24). New displacement 10,150 t.
  2. KG = (10,000 × 7.00 + 150 × 22) ÷ 10,150 = 73,300 ÷ 10,150 = 7.222 m; GM = 8.00 − 7.222 = 0.778 m.
  3. Transverse shift of G = 150 × 14 ÷ 10,150 = 0.207 m.
  4. tan list = 0.207 ÷ 0.778 = 0.266, so the list is about 14.9°.
  5. Check against question 11's method (tan list = GG1 ÷ GM). A 15° list with a load swinging overhead is why the chief mate fills or empties wing tanks to pre-list the ship before the lift.

Example 3: final draughts after loading off the LCF. Length 150 m; LCF 3 m abaft midships (72 m from the after perpendicular). Draughts F 7.80 m, A 8.20 m. Load 240 t at 30 m forward of the LCF. TPC 24, MCTC 180 t-m/cm.

  1. Bodily sinkage = 240 ÷ 24 = 10 cm.
  2. Change of trim = 240 × 30 ÷ 180 = 40 cm by the head.
  3. Share of the trim change aft = 40 × 72 ÷ 150 = 19.2 cm (aft draught decreases); forward = 40 − 19.2 = 20.8 cm (forward draught increases).
  4. New aft draught = 8.20 + 0.10 − 0.192 = 8.108 m; new forward draught = 7.80 + 0.10 + 0.208 = 8.108 m: even keel.
  5. Check: the original trim was 40 cm by the stern and the change was 40 cm by the head, so even keel is right. Questions 20 to 22 use the same steps.

Example 4: dock water allowance and loading draught. Summer draught 9.50 m, FWA 220 mm, dock water density 1.012 t/m³.

  1. DWA = FWA × (1.025 − 1.012) ÷ 0.025 = 220 × 0.52 = 114 mm.
  2. The ship may load until her mean draught in the dock is 9.50 + 0.114 = 9.61 m, and she will rise to her summer mark in sea water.
  3. Check: dock water between fresh and salt gives an allowance between zero and the full FWA, and 114 mm is about half of 220 mm because 1.012 is about halfway. Questions 17 to 19 test the same logic.

The stability calculations blog walks through more cases, and the ship stability oral topic covers how to explain them aloud.

Which traps does this set use, and what is the rule?

These are the distractor patterns in this set, the rule that defeats each and the questions where they appear.

  • Formula rearranged wrongly. Questions 1 and 3. Rule: GM = KM − KG and KM = KB + BM.
  • Old displacement used. Questions 4 and 5 offer the KG you get by dividing by the old displacement. Rule: total moment ÷ final displacement.
  • Free surface added instead of subtracted. Question 6. Rule: fluid GM = solid GM − FSC.
  • Free surface moment arithmetic. Questions 7, 8 and 10. Rule: FSM = l × b³ ÷ 12 × ρ (t-m); FSC = FSM ÷ Δ; it does not depend on the amount of liquid in a box-shaped tank.
  • Subdivision factor. Question 9. Rule: one centreline bulkhead cuts the free surface moment to a quarter (the breadth is halved and cubed, then there are two tanks).
  • Tangent forgotten. Questions 11 and 40. Rule: tan list = GG1 ÷ GM, and listing moment = Δ × GM × tan θ.
  • Vertical shift with displacement changed. Question 12. Rule: a shift on board moves G by w × d ÷ Δ with Δ unchanged.
  • List and loll confused. Questions 13 and 14. Rule: loll comes from negative GM with G on the centreline; lower G with divided low-side tanks first; never shift weight to the high side.
  • TPC and FWA units. Questions 15 to 19. Rule: sinkage (cm) = w ÷ TPC; TPC = A × ρ ÷ 100; FWA (mm) = Δ ÷ (4 × TPC); DWA = FWA × (1.025 − ρ) ÷ 0.025; in dock water load deeper than the summer mark by the DWA.
  • Trim direction or LCF ignored. Questions 20, 21 and 22. Rule: change of trim = w × d ÷ MCTC, towards the end the weight moves; weight over the LCF gives parallel sinkage.
  • Small-angle GZ. Question 23. Rule: GZ = GM × sin θ only at small angles.
  • Suspended weight at its own Kg. Question 24. Rule: it acts at the derrick or crane head from the moment it lifts.
  • IS Code numbers swapped. Questions 25 to 30. Rule (IS Code 2008 Part A, 2.2): area 0.055 m-rad to 30°, 0.09 to 40°, 0.03 between; GZ at least 0.20 m at 30° or more; maximum GZ at not less than 25°; GM0 at least 0.15 m; steady-wind heel limit 16° or 80% of deck-edge immersion.
  • Grain Code numbers swapped. Questions 31, 32 and 33. Rule: heel from grain shift not more than 12°; GM at least 0.30 m; residual area at least 0.075 m-rad.
  • Rolling period read backwards. Question 34. Rule: a short, jerky roll means a large GM (stiff ship).
  • Ice and ballast effects reversed. Questions 36 and 39. Rule: ice adds weight high and windage (G up, GM down); a pressed-up double bottom adds weight low with no free surface (GM up).

The common-traps section above names the five habits that cost most marks; this list maps every pattern to its questions.

Revision table

Formulas and criteria this set uses.

Ship stability revision table
TopicNumber or ruleReference
Metacentric heightGM = KM − KG; KM = KB + BMStability theory
New KGΣ moments ÷ final displacementMoments about the keel
Free surfaceFSM = l b³ ÷ 12 × ρ; FSC = FSM ÷ ΔStability theory
Listtan θ = GG1 ÷ GMStability theory
Sinkage and trimw ÷ TPC; w × d ÷ MCTCHydrostatics
FWAΔ ÷ (4 × TPC) mmLoad Lines 1966, Annex I
DWAFWA × (1.025 − ρ) ÷ 0.025Load Lines 1966, Annex I
Area under GZ0.055 to 30°; 0.09 to 40°; 0.03 between (m-rad)IS Code 2008 Part A, 2.2.1
GZ and GM0GZ ≥ 0.20 m at ≥ 30°; max GZ at ≥ 25°; GM0 ≥ 0.15 mIS Code 2008 Part A, 2.2.2–2.2.4
Weather criterionSteady-wind heel ≤ 16° or 80% deck-edge angleIS Code 2008 Part A, 2.3
GrainHeel ≤ 12°; GM ≥ 0.30 m; residual area ≥ 0.075 m-radInternational Grain Code, A 7.1
Heavy liftWeight acts at the derrick head once liftedStability theory

Where is ship stability examined?

Stability is examined at every deck certificate level, from operational level (officer of the watch) to management level (chief mate and master), in both the written papers and the oral. At operational level you are expected to use the stability booklet and do the standard calculations. At management level you are expected to judge whether the ship complies, handle damage and grain cases, and explain the theory behind the numbers.

Use these pages for each country's exam structure:

Stability questions also appear in company screening tests such as the CES test for deck officers and in deck officer interviews.

What should you study after this set?

Stability links straight into cargo work and ship construction. After this set, try the cargo work MCQ for grain, bulk and load line questions, and the SOLAS MCQ for the damage stability and watertight door rules. For the oral, read cargo work, ship construction and tanker operations, because examiners move from free surface to tank cleaning and from loading to hull stress in one conversation.

If your exam is close, follow the 30-day oral preparation plan and put one stability calculation in every study day.

Practice set

40 practice questions with answers

Pick an answer to see if it is right and why. Your score stays on this page only.

–0/40 done
  1. 1
    CoreStability theory: metacentric height

    How is the metacentric height (GM) of a ship found?

    Show answer

    Answer: C. GM is the distance from the centre of gravity G up to the metacentre M, so it is KM minus KG. KB + BM gives KM itself, not GM, which is the tempting wrong choice; adding BG to it is a sign slip.

  2. 2
    CoreStability theory: equilibrium

    A ship is in stable equilibrium at small angles of heel when:

    Show answer

    Answer: A. With G below M, the weight and buoyancy form a righting couple when the ship heels. B is normally below G on a ship, so a rule based on B being above G is wrong.

  3. 3
    CoreStability theory: KM = KB + BM

    KM for a ship at a given draught is found from:

    Show answer

    Answer: D. KM depends only on the underwater shape at that draught: the height of the centre of buoyancy (KB) plus the metacentric radius BM = I ÷ V. KB + BG gives KG, which is a loading condition, and the free surface correction changes GM, not KM.

  4. 4
    DeeperStability theory: KG by moments about the keel

    A ship of 10,000 t displacement has KG 7.0 m. She loads 500 t of cargo with its centre of gravity at 12.0 m above the keel. What is the new KG?

    Show answer

    Answer: B. Moments: 10,000 × 7.0 = 70,000 t-m plus 500 × 12.0 = 6,000 t-m gives 76,000 t-m over the new displacement of 10,500 t, so KG = 7.24 m. Dividing by the old displacement gives 7.60 m, and adding 6,000 ÷ 10,500 to the old KG (ignoring that G already sits at 7.0 m) gives 7.571 m.

  5. 5
    DeeperStability theory: KG by moments about the keel

    A ship of 12,000 t displacement has KG 8.0 m. She discharges 2,000 t of cargo from a lower hold with Kg 4.0 m. What is the new KG?

    Show answer

    Answer: B. Moments: 12,000 × 8.0 = 96,000 t-m minus 2,000 × 4.0 = 8,000 t-m gives 88,000 t-m over the new displacement of 10,000 t, so KG = 8.80 m. Dividing the moment by the old displacement (12,000 t) gives 8.667 m. Taking weight off low down raises G, so discharging bottom cargo first reduces GM.

  6. 6
    DeeperStability theory: free surface correction

    A ship has KM 8.60 m and KG 7.90 m. A slack fresh water tank gives a free surface correction of 0.167 m. What is the effective (fluid) GM?

    Show answer

    Answer: D. Solid GM = 8.60 − 7.90 = 0.70 m. Fluid GM = 0.70 − 0.167 = 0.53 m. Adding the correction instead of subtracting it gives 0.867 m, which is wrong because free surface always reduces GM.

  7. 7
    DeeperStability theory: FSM = l b³/12 × ρ

    A rectangular tank 20 m long and 10 m wide is slack with fresh water (density 1.000 t/m³). The ship displaces 10,000 t. What is the free surface correction?

    Show answer

    Answer: A. FSM = l × b³ ÷ 12 × density = 20 × 1,000 ÷ 12 × 1.000 = 1,666.7 t-m. FSC = 1,666.7 ÷ 10,000 = 0.167 m, about 0.17 m. Forgetting to cube the breadth gives 0.0167 m, and dividing by 1,000 t instead of 10,000 t gives 1.67 m.

  8. 8
    DeeperStability theory: FSM = l b³/12 × ρ

    A slack ballast tank (salt water, 1.025 t/m³) is 15 m long and 12 m wide. The ship displaces 15,000 t. What is the free surface correction?

    Show answer

    Answer: C. FSM = 15 × 12³ ÷ 12 × 1.025 = 15 × 1,728 ÷ 12 × 1.025 = 2,214 t-m. FSC = 2,214 ÷ 15,000 = 0.148 m, about 0.15 m. Leaving out the density of the liquid gives 0.144 m, and forgetting to divide by 12 gives 1.77 m.

  9. 9
    DeeperStability theory: subdivision of tanks

    A slack tank is divided by one longitudinal centreline bulkhead into two equal tanks. What happens to the free surface moment?

    Show answer

    Answer: D. Each half has breadth b/2, so each has 1/8 of the original FSM, and two halves give 2/8 = 1/4. Halving is the tempting answer because the breadth is halved, but FSM depends on breadth cubed.

  10. 10
    TrapStability theory: free surface effect

    For a box-shaped slack tank, the free surface moment depends on:

    Show answer

    Answer: C. FSM = l × b³ ÷ 12 × density. The amount of liquid and the tank's height do not appear in the formula, which is why a nearly empty tank can be as dangerous as a half-full one; breadth counts as a cube, not a square.

  11. 11
    DeeperStability theory: tan list = GG1 ÷ GM

    A ship of 10,000 t displacement with GM 1.5 m shifts 200 t of cargo 15 m transversely. What angle of list results?

    Show answer

    Answer: B. GG1 = 200 × 15 ÷ 10,000 = 0.30 m. tan θ = GG1 ÷ GM = 0.30 ÷ 1.5 = 0.20, so θ = 11.3°. Taking tan θ = 0.30 without dividing by GM gives 16.7°. The list grows as GM falls, which is why the same shift is far worse on a tender ship.

  12. 12
    DeeperStability theory: GG1 = w d / Δ

    A ship of 15,000 t displacement moves 300 t of cargo from a 'tween deck (Kg 14 m) to a lower hold (Kg 2 m). What happens to G?

    Show answer

    Answer: A. Shift of G = w × d ÷ Δ = 300 × 12 ÷ 15,000 = 0.24 m, downwards because the weight moved down. A shift of weight within the ship does not change displacement.

  13. 13
    TrapStability theory: angle of loll

    A ship floating upright suddenly takes up an angle of about 6° to port; when weight is moved, she flops over to about 6° starboard. G is on the centreline. What is the most likely cause?

    Show answer

    Answer: A. A ship that lies over to either side with G on the centreline has negative initial GM and is lolling. A list from an off-centre weight would always be to the same side.

  14. 14
    TrapStability theory: correcting loll

    What is the correct way to deal with an angle of loll?

    Show answer

    Answer: B. Loll is a negative GM, so the cure is to lower G and remove free surface. Moving or adding weight on the high side can make the ship flop over violently to the other side, and pumping out low ballast raises G further.

  15. 15
    CoreStability theory: TPC

    A ship with TPC 25 t/cm loads 300 t of cargo at the LCF. What is the bodily sinkage?

    Show answer

    Answer: C. Sinkage = w ÷ TPC = 300 ÷ 25 = 12 cm. Because the weight is loaded at the LCF, there is no change of trim, only parallel sinkage.

  16. 16
    CoreStability theory: TPC = A × ρ / 100

    A ship has a waterplane area of 2,000 m² at her present draught. What is her TPC in salt water of 1.025 t/m³?

    Show answer

    Answer: D. TPC = A × density ÷ 100 = 2,000 × 1.025 ÷ 100 = 20.5 t/cm. Using 1.000 gives the fresh water TPC of 20.0 t/cm, the tempting wrong answer, and leaving out the ÷ 100 gives 2,050.

  17. 17
    CoreInternational Convention on Load Lines 1966, Annex I (fresh water allowance)

    A ship's summer displacement is 20,000 t and TPC 25 t/cm. What is her fresh water allowance?

    Show answer

    Answer: C. FWA (mm) = Δ ÷ (4 × TPC) = 20,000 ÷ 100 = 200 mm. This is how far the mean draught increases going from salt water (1.025) to fresh water (1.000).

  18. 18
    DeeperInternational Convention on Load Lines 1966, Annex I (dock water allowance)

    A ship with FWA 200 mm is loading in a dock where the water density is 1.010 t/m³. What is the dock water allowance?

    Show answer

    Answer: A. DWA = FWA × (1,025 − 1,010) ÷ 25 = 200 × 15 ÷ 25 = 120 mm. Using (1,010 − 1,000) gives 80 mm, which is the amount by which DWA is less than FWA, not the DWA itself.

  19. 19
    TrapInternational Convention on Load Lines 1966, Annex I

    A ship loading in dock water of density 1.010 t/m³ wants to reach her summer load line on reaching the sea. Compared with the summer mark, her loaded draught in the dock should be:

    Show answer

    Answer: D. In less dense water the ship floats deeper for the same displacement, so she may submerge the summer mark by the DWA in the dock and rise to it in salt water. Using the full FWA would only be right in water of 1.000 t/m³.

  20. 20
    DeeperStability theory: change of trim = moment ÷ MCTC

    150 t of cargo is moved 40 m aft. MCTC is 200 t-m/cm. What is the change of trim?

    Show answer

    Answer: B. Trimming moment = 150 × 40 = 6,000 t-m. Change of trim = 6,000 ÷ 200 = 30 cm, by the stern because the weight moved aft. MCTC is already per centimetre, so there is no further conversion; 300 cm is a units slip.

  21. 21
    DeeperStability theory: sinkage and trim

    A ship with TPC 20 t/cm and MCTC 160 t-m/cm loads 200 t at 20 m abaft the LCF. What are the sinkage and change of trim?

    Show answer

    Answer: B. Sinkage = 200 ÷ 20 = 10 cm. Trimming moment = 200 × 20 = 4,000 t-m, so trim change = 4,000 ÷ 160 = 25 cm by the stern because the weight is aft of the LCF.

  22. 22
    CoreStability theory: centre of flotation

    Cargo is loaded exactly over the centre of flotation (LCF). What happens?

    Show answer

    Answer: D. The ship trims about the LCF, so a weight placed vertically over it causes no trimming moment and only bodily sinkage. Many candidates confuse the LCF with the LCB or midships.

  23. 23
    CoreStability theory: GZ = GM sin θ

    At small angles of heel, a ship with GM 0.8 m heels to 5°. What is the righting lever GZ?

    Show answer

    Answer: A. GZ = GM × sin θ = 0.8 × sin 5° = 0.8 × 0.0872 = 0.070 m. A calculator left in radian mode gives about 0.767 m. This small-angle formula only holds up to about 10 to 15 degrees; beyond that read GZ from the cross curves.

  24. 24
    TrapStability theory: suspended weights

    A ship of 8,000 t displacement, KG 6.5 m, lifts a 100 t package off the quay with her own heavy derrick. The derrick head is 20 m above the keel. What is KG at the moment the package is lifted clear?

    Show answer

    Answer: C. As soon as a weight is suspended, it acts at the point of suspension. Moments: 8,000 × 6.5 = 52,000 plus 100 × 20 = 2,000 gives 54,000 t-m over 8,100 t, so KG = 6.67 m. Thinking KG stays unchanged until the package is landed is the trap, and dividing by 8,000 t instead of 8,100 t gives 6.75 m.

  25. 25
    CoreIS Code 2008 Part A, 2.2.1

    Under Part A of the IS Code 2008, the minimum area under the GZ curve up to 30° heel is:

    Show answer

    Answer: D. The criteria are 0.055 m-rad up to 30°, 0.09 m-rad up to 40° (or the flooding angle) and 0.03 m-rad between 30° and 40°. The 0.075 m-rad figure is the Grain Code residual area, a common mix-up.

  26. 26
    CoreIS Code 2008 Part A, 2.2.2

    Under Part A of the IS Code 2008, the righting lever GZ must be at least:

    Show answer

    Answer: C. The code requires GZ of at least 0.20 m at an angle of heel equal to or greater than 30°. The 0.15 m figure is the minimum initial GM, not GZ, and 25° is the minimum angle for maximum GZ.

  27. 27
    CoreIS Code 2008 Part A, 2.2.4

    Under Part A of the IS Code 2008, the minimum initial metacentric height GM0 is:

    Show answer

    Answer: B. Initial GM must be at least 0.15 m (corrected for free surface). The 0.30 m figure is the Grain Code minimum for ships carrying bulk grain.

  28. 28
    DeeperIS Code 2008 Part A, 2.2.3

    Under Part A of the IS Code 2008, the maximum righting lever should occur at an angle of heel of:

    Show answer

    Answer: A. The maximum GZ must occur at an angle of not less than 25°. The code says it should preferably exceed 30°, but 25° is the minimum; 35° or 40° are not IS Code figures for this criterion.

  29. 29
    DeeperIS Code 2008 Part A, 2.3.1

    In the IS Code 2008 severe wind and rolling (weather) criterion, the angle of heel under the steady wind should, as a guide, be limited to:

    Show answer

    Answer: A. Under the weather criterion the steady wind heel is limited to the Administration's satisfaction, with 16° or 80% of the deck-edge immersion angle, whichever is less, given as the guide. 12° is the Grain Code limit for heel from grain shift.

  30. 30
    CoreIS Code 2008, Introduction; SOLAS Ch. II-1 Reg. 2

    Which part of the 2008 Intact Stability Code is mandatory?

    Show answer

    Answer: B. Part A holds the mandatory criteria made binding through SOLAS and the 1988 Load Lines Protocol from 1 July 2010; Part B contains recommendations and guidance. This is the same A-mandatory, B-guidance pattern as the ISPS Code.

  31. 31
    CoreInternational Grain Code, Part A, 7.1

    Under the International Grain Code, the angle of heel due to the assumed shift of grain must not be more than:

    Show answer

    Answer: C. The Grain Code limits the heel from grain shift to 12°, or for ships built on or after 1 January 1994 the deck-edge immersion angle if that is less. 16° belongs to the IS Code weather criterion, the usual wrong pick.

  32. 32
    CoreInternational Grain Code, Part A, 7.1

    Under the International Grain Code, the minimum initial GM after correction for free surface of liquids in tanks is:

    Show answer

    Answer: D. A ship carrying bulk grain must have at least 0.30 m of fluid GM. The 0.15 m value is the general IS Code minimum and is not enough for grain.

  33. 33
    DeeperInternational Grain Code, Part A, 7.1

    Under the International Grain Code, the residual area between the heeling arm curve and the righting arm curve must be at least:

    Show answer

    Answer: C. The residual dynamic stability must be at least 0.075 m-rad, measured up to 40°, the flooding angle or the angle of maximum difference between the curves, whichever is least. 0.055 m-rad is the IS Code area to 30°.

  34. 34
    CoreStability theory: rolling period and GM

    A ship has a very short, quick and jerky rolling period at sea. What does this tell you?

    Show answer

    Answer: A. Rolling period is inversely proportional to the square root of GM, so a short period means a large GM. A stiff ship is safe from capsize but rolls violently, stressing lashings and cargo.

  35. 35
    CoreSOLAS Ch. II-1 Reg. 5

    What is the main purpose of the inclining experiment on a new ship?

    Show answer

    Answer: D. The inclining test measures GM, from which the lightship KG is derived; it is the starting point for every loading calculation in the stability booklet. KM at each draught comes from hydrostatic calculations, not from the test.

  36. 36
    TrapIS Code 2008 Part B, Ch. 6 (icing considerations)

    During a winter voyage, ice builds up on the deck, masts and rigging. What is the effect on stability?

    Show answer

    Answer: B. Ice is a high weight, so it raises G and reduces GM; it can also be uneven and cause a list. The small increase in draught does not offset this, which is why ice must be removed early.

  37. 37
    DeeperStability theory: dynamical stability

    Dynamical stability at a given angle of heel is:

    Show answer

    Answer: B. Dynamical stability is the work done in heeling the ship, which equals displacement times the area under the GZ curve. GZ times displacement is the righting moment at one angle, not the work done.

  38. 38
    CoreStability theory: GZ curve

    The angle of vanishing stability is the angle of heel at which:

    Show answer

    Answer: D. The range of stability ends where the GZ curve crosses back to zero; beyond it the ship will capsize. Maximum GZ comes earlier, and deck-edge immersion is usually where the curve's slope starts to fall.

  39. 39
    CoreStability theory: effect of ballasting

    A ship fills an empty double bottom ballast tank completely (pressed up). What is the usual effect on GM?

    Show answer

    Answer: A. Adding weight below G lowers G, and a pressed-up tank has no free surface, so GM rises. The free surface penalty only applies while the tank is being filled and is slack.

  40. 40
    DeeperStability theory: list correction

    A ship of 12,000 t displacement has GM 0.6 m. To correct a 3° list, what listing moment must be removed?

    Show answer

    Answer: C. GG1 = GM × tan θ = 0.6 × tan 3° = 0.6 × 0.0524 = 0.0314 m. Listing moment = Δ × GG1 = 12,000 × 0.0314 = 377 t-m. 7,200 t-m is Δ × GM with the angle left out.

Reading answers is not the same as saying them. Our AI voice examiner asks these out loud, listens to your answer, asks the follow-up and marks you against the rule. Join early access or try the free timed mock oral drill.

Frequently asked questions

What is a good GM for a cargo ship?

There is no single good value; it depends on the ship type and the voyage. The IS Code 2008 sets a minimum initial GM of 0.15 m for most cargo ships, and the Grain Code needs at least 0.30 m when carrying grain. Too large a GM makes the ship stiff, with a short, violent roll that can damage cargo and injure crew.

How do you calculate the new KG after loading cargo?

Multiply the old displacement by the old KG to get the old moment, add the weight times its Kg for each item loaded, and subtract it for each item discharged. Divide the total moment by the new displacement. The most common mistake is dividing by the old displacement.

What is free surface effect in simple words?

When liquid in a slack tank moves to the low side as the ship heels, it shifts the ship's centre of gravity sideways. The effect is the same as if G had risen, so we call it a virtual rise of G. It reduces the effective GM.

Does a half-full tank have more free surface effect than a nearly full one?

For a box-shaped tank, no. The free surface moment depends on the tank's length, the cube of its breadth and the density of the liquid, not on the depth of liquid. A pressed-up or empty tank has no free surface.

What is the difference between list and loll?

A list is caused by G being off the centreline while GM is positive. A loll is caused by a negative GM with G on the centreline; the ship lies to one side and may flop to the other. They need opposite corrections, so identifying which one you have comes first.

How do you correct an angle of loll?

Lower the centre of gravity. Ballast divided double bottom tanks starting with the low side, remove or lower high weights, and remove free surface where you can. Do not move weight to the high side, because the ship can flop over to the other side with a greater angle.

What is the formula for FWA?

FWA in millimetres equals the summer displacement in tonnes divided by four times the TPC in salt water. It is the amount the ship's mean draught increases when she passes from salt water of 1.025 t/m³ to fresh water of 1.000 t/m³.

What are the IS Code 2008 intact stability criteria?

Part A 2.2 requires at least 0.055 m-rad of area under the GZ curve to 30°, 0.09 m-rad to 40° or the flooding angle, and 0.03 m-rad between 30° and 40°. GZ must be at least 0.20 m at 30° or more, maximum GZ must occur at 25° or more, and initial GM must be at least 0.15 m. Part A also includes a severe wind and rolling (weather) criterion.

What are the Grain Code stability criteria?

The angle of heel from the assumed grain shift must not exceed 12°, the residual area between the heeling arm and righting arm curves must be at least 0.075 m-rad, and the initial GM corrected for free surface must be at least 0.30 m. These are in section A 7 of the International Grain Code.

Why does a ship's rolling period tell you about GM?

The rolling period is inversely proportional to the square root of GM. A short, quick roll means a large GM (a stiff ship); a long, slow roll means a small GM (a tender ship). A sudden lengthening of the roll period is a warning that GM has fallen.

Are these the questions asked in the MMD or MCA exam?

No. We wrote every question ourselves around the published syllabus and the IS Code, Grain Code and Load Line Convention. They show the kind of question you should expect and the calculations you must be able to do, not items from any exam paper.

How many stability calculations should I practise before the written exam?

Practise until each standard type (KG, free surface, list, TPC, FWA and DWA, trim, heavy lift) is automatic and you can do it without notes. Most candidates need several worked examples of each type. Time yourself, because written papers are timed.

Sources 1 document

Each number in the text links to the source below. Labels show the type of source; see our editorial policy.

  1. Official IMO Resolution MSC.267(85), International Code on Intact Stability, 2008 · 4 December 2008

Where should you go next?

  • Question banks7 pages: free MCQ sets with answers and explanations
  • Oral topics14 pages: examiner questions with model answer points, deck and engine
  • CoC exam guides16 pages: every oral and written exam, authority by authority
  • Free tools4 pages: mock oral drill, lights trainer, sea-time calculator, practice tests
Exam Prep DeskMaritime exam researchers

We write from the conventions (STCW, COLREG, SOLAS, MARPOL), the authorities' own notices and published syllabi, and cite the source for every fee, rule and date. We are independent and not linked to any maritime administration or test provider. Found an error? It matters at sea: tell us and see how we correct · Disclaimer.

Related guides

AI voice mock oral

Say it out loud before the examiner asks.

Our examiner asks CoC oral questions by rank and function, listens to your answer, asks the follow-up and scores you against the rule. Early access is open for India first.

  • Deck and engine, every rank
  • Answers referenced to the conventions
  • Independent, not linked to any authority
WhatsApp us