On this page
- Key facts
- How should you use this main engine MCQ set?
- What are the 10 main engine facts you must know?
- Which main engine questions do candidates get wrong most often?
- How do you work the calculation questions on main engines?
- Which traps does this main engine set use, and what is the rule?
- Main engine revision table
- Where are main engine questions examined?
- What should you study after this set?
- 40 practice questions
- Frequently asked questions
- Sources
Key facts
- Questions
- 38 MCQs, 4 options each
- Level
- Core, deeper and trap questions
- Best for
- MEO Class 4 and Class 2, EOOW, second engineer, CES engine
- Topics
- Scavenge fires, crankcase safety, starting air, indicator cards, timing, turbochargers
- Calculations
- Mean indicated pressure, fuel consumption, propeller slip
- Rules cited
- SOLAS Ch. II-1 Reg. 27, class rules, maker's practice
- Time to finish
- About 40 minutes
- Cost
- Free, no sign-up
Checked 14 November 2026. Fees and rules change: confirm with the authority before you book.
How should you use this main engine MCQ set?
Answer each question before you open the explanation, then read the explanation even when you were right. The set is ordered from core knowledge to deeper diagnosis and finally to trap questions, where the obvious answer is wrong.
Multiple-choice practice builds recall. An oral examiner wants more: the reason, the sequence of actions and the safety point. After each block of ten questions, take one wrong answer and explain it out loud for two minutes as if you were in front of an examiner. Our free mock oral drill gives you examiner-style prompts for that, and the practice test tool lets you time yourself on mixed sets.
Use the set in three passes:
- Pass 1, cold. Do all 40 questions without notes. Mark every guess, even if it was right.
- Pass 2, read. Read the matching section of the two-stroke main engine oral topic and the engine maker's instruction book for your last ship.
- Pass 3, speak. Explain the scavenge fire and crankcase explosion sequences aloud without looking. These two come up in almost every engine oral.
If you want an examiner that asks follow-ups and scores you, join early access for our AI voice mock examiner.
What are the 10 main engine facts you must know?
These ten points carry most of the marks on main engine questions. Learn the number or the sequence, then the reason behind it.
| Item | What to know | Source |
|---|---|---|
| Crankcase relief valves | Required on engines with cylinder diameter of 200 mm or more, or crankcase volume of 0.6 m³ or more | SOLAS Ch. II-1 Reg. 27 |
| Relief valve design | Opens quickly, recloses to stop air inrush, flame arrester fitted | SOLAS Ch. II-1 Reg. 27; IACS UR M9 |
| Oil mist detection | Engines of 2,250 kW and above, or bore over 300 mm, need oil mist detectors, bearing temperature monitors or equivalent | SOLAS Ch. II-1 Reg. 27 |
| Crankcase doors after mist alarm | Do not open until the engine has cooled for the maker's stated time | Maker's instructions |
| Scavenge fire first action | Reduce speed, cut fuel to the unit, increase cylinder oil, keep doors shut | Maker's instructions |
| Starting air capacity | Reversible engines: at least 12 consecutive starts alternating ahead and astern | Classification society rules |
| Starting air line protection | Flame arrester or bursting disc near each cylinder starting valve | Classification society rules |
| Mean indicated pressure | Card area ÷ card length ÷ spring scale | Engineering principle |
| Cylinder oil BN | Match base number to fuel sulphur; low BN with low-sulphur fuel | Maker's guidance |
| Barred speed range | Do not run continuously in it: torsional vibration resonance | Class rules, engine plate |
Which main engine questions do candidates get wrong most often?
Most wrong answers come from mixing up the scavenge space and the crankcase. They are separate spaces on a crosshead engine, and the actions for a fire in each are different.
- Opening doors too early. For both a scavenge fire and an oil mist alarm, opening doors lets in air. In the crankcase this can cause a second, bigger explosion. Wait for the engine to cool.
- Late injection vs leaking exhaust valve. Late injection gives low peak pressure with normal compression pressure. A leaking exhaust valve or broken rings lowers compression pressure too. The indicator card tells you which.
- Flame arrester vs relief valve. The relief valve releases pressure. The flame arrester stops the flame from leaving the crankcase and hitting people.
- Surging cause. Surging is a compressor flow problem, often from fouled turbine nozzles, fouled scavenge ports or sudden load changes, not from too much fuel alone.
- Cylinder oil BN. Since the 0.50% global sulphur cap came in[1], many ships burn low-sulphur fuel. Using high-BN oil with it leaves calcium deposits and bore polish. The fix is lower BN or a lower feed rate as the maker advises.
- Starting air valve leak. The sign is a hot branch pipe to that unit, not a pressure drop at the receiver.
For the engineering side of the sulphur rules, see fuel sulphur rules and scrubbers.
How do you work the calculation questions on main engines?
Main engine questions use five standard calculations. In each one, decide first whether the engine is two-stroke (one power stroke per revolution) or four-stroke (one per two revolutions); that one choice decides half the answers in this set.
Example 1: mean indicated pressure from a card (question 17). Mean height of the card = area ÷ length = 540 mm² ÷ 60 mm = 9.0 mm. Divide by the spring scale: 9.0 ÷ 0.5 mm/bar = 18 bar. If you multiply by the spring scale instead, you get 4.5 bar, which is far too low for a loaded engine: a quick sanity check catches it.
Example 2: indicated power (question 18). P = pmi × A × L × n × cylinders, with n in power strokes per second. Bore 0.5 m gives A = π × 0.25² = 0.1963 m². For one cylinder: 1,800 kPa × 0.1963 × 2.0 × (100 ÷ 60) = 1,178 kW. Six cylinders: 7,069 kW, which rounds to 7,070 kW. On a four-stroke you halve n, so the same numbers would give 3,530 kW.
Example 3: daily fuel (question 23). 10,000 kW × 170 g/kWh = 1,700,000 g/h = 1.7 t/h; × 24 = 40.8 t/day. Converting to volume for tank planning: at a density of 0.98 t/m³ this is 40.8 ÷ 0.98 = 41.6 m³ per day.
Example 4: propeller slip (question 24). Engine speed = 5 × 100 × 60 ÷ 1,852 = 16.20 kn. Slip = (16.20 − 15) ÷ 16.20 = 7.4%. Watch the slip over months at the same draught: a steady rise points to hull or propeller fouling.
Example 5: mean piston speed and cylinder oil (question 40). Mean piston speed = 2 × stroke × rpm ÷ 60 = 2 × 2.0 × 100 ÷ 60 = 6.7 m/s. Cylinder oil is usually set as a feed rate in g/kWh from the engine maker's guidance. As an illustration, a feed rate of 0.8 g/kWh at 10,000 kW is 8,000 g/h, so 8 kg/h or 192 kg per day. If the scavenge inspection shows dry, polished liners or heavy deposits, the feed rate and the oil's BN are adjusted to the fuel sulphur (question 31), following the maker's guidance rather than a fixed number.
Examiner's note: The examiner who asks for indicated power usually follows with "what is the difference between indicated and brake power?" The strong answer: brake power is indicated power less mechanical losses, mechanical efficiency is brake ÷ indicated, and on a large two-stroke it is typically high, so a big gap points to friction, bearing or measurement problems.
Which traps does this main engine set use, and what is the rule?
Main engine distractors mostly reverse a cause and effect, swap a two-stroke figure for a four-stroke one, or put the repair before the safety step.
| Trap pattern | Questions | Rule that defeats it |
|---|---|---|
| Repair before safety | 3, 9, 15 | Scavenge fire: inform the bridge, slow down, cut fuel to the unit, raise its lube oil, keep doors shut. Oil mist alarm: keep away from doors and relief valves, stop, wait to cool. Blow through before starting. |
| Crankcase rules mixed | 4, 5, 6, 7 | Relief valves from 200 mm bore or 0.6 m³; they must reclose to stop air entering; the flame arrester quenches the flame; oil mist detection from 2,250 kW or bores above 300 mm. |
| Ignition source confused | 1, 10 | Scavenge fire: blow-by igniting oil residue. Crankcase explosion: hot spot plus oil mist. |
| Starting air numbers | 12, 13, 14, 16 | Reversible engine 12 starts; non-reversible 6. Hot branch pipe = leaking starting air valve. Bursting discs limit explosion damage. Turning gear interlock blocks starting air. |
| Two-stroke vs four-stroke counting | 18, 40 | Two-stroke n = rpm ÷ 60 power strokes per second; four-stroke n = rpm ÷ 120. Piston speed counts two strokes per revolution. |
| Card and fault reading | 19, 20, 21, 36 | Draw card shows compression, peak and ignition point. Normal compression + low Pmax = injection fault. Low compression + low Pmax = valve or rings. |
| Formula base | 17, 24 | MIP = mean height ÷ spring scale. Slip is divided by engine speed. |
| Cold corrosion and BN | 30, 31 | Cold corrosion is sulphuric acid below the dew point. With low-sulphur fuel, lower BN or adjust feed rate, guided by the maker and scavenge inspections. |
| Symptom of gas in water | 32 | Gas venting from the expansion tank with pressure swings means a cracked liner or cover. |
| Governor vs safety device | 39 | The overspeed trip cuts fuel independently of the governor. |
If two options look right, pick the one that names the root cause (blow-by, hot spot, leaking valve) over the one that names a later symptom.
Main engine revision table
Use this as a last-hour check.
| Topic | Recall | Questions |
|---|---|---|
| Scavenge fire | Blow-by ignites residue; slow down, cut fuel, keep doors shut | 1–3 |
| Crankcase safety | 200 mm / 0.6 m³ relief valves; OMD from 2,250 kW or bore over 300 mm | 4–10 |
| Starting air | 12 starts reversible, 6 non-reversible; hot branch = leaking valve | 12–16 |
| Indicator cards | MIP = area ÷ length ÷ spring scale; draw card for ignition | 17, 19 |
| Power | P = pmi × A × L × n × cylinders | 18 |
| Faults | Late injection vs leaking exhaust valve | 20, 21, 36, 37 |
| Fuel and slip | SFOC × power × 24; slip ÷ engine speed | 23, 24 |
| Scavenging and valves | Uniflow; air spring closes exhaust valve; aux blowers at low load | 26–28 |
| Liners | Cold corrosion; match BN to sulphur; cracked liner gas in jacket water | 30–32 |
| Running limits | Barred speed range; overspeed trip independent; EIAPP for NOx | 34, 38, 39 |
Where are main engine questions examined?
Main engine knowledge is tested at every engine certificate level and in most company screening tests. The depth changes with rank: operational level candidates must describe the system and the immediate actions; management level candidates must diagnose faults, interpret indicator cards and talk about maintenance planning.
- India: the MEO Class 4 oral, MEO Class 2 oral and MEO Class 1 oral.
- UK: the MCA EOOW oral, MCA second engineer oral, MCA chief engineer oral and the SQA written exams.
- USA: the USCG engineer license exams.
- Philippines: the MARINA officer exams.
- Australia and Singapore: the AMSA oral exams and MPA CoC oral exams.
- Job screening: CES for engineers and marine engineer interview questions.
What should you study after this set?
Move to the systems that feed and protect the main engine. Each has its own oral topic page and, where we have one, an MCQ set.
- Air compressors and starting air for the starting sequence and air line explosions.
- Fuel oil purifiers and the pumps and purifiers MCQ, because poor fuel treatment causes many engine faults.
- Auxiliary diesel engines for four-stroke differences.
- UMS and automation for slowdowns, shutdowns and alarms.
- Engine room watchkeeping for what to check on rounds.
- The marine boilers MCQ and the CES engine practice set.
Before an oral, run through the 30-day oral preparation plan and the books for MEO Class 4.
Practice set
40 practice questions with answers
Pick an answer to see if it is right and why. Your score stays on this page only.
- 1
What is the most common cause of a scavenge fire in a two-stroke crosshead engine?
Show answer
Answer: C. Blow-by past worn, stuck or broken rings carries flame into a scavenge space fouled with cylinder oil and carbon. A dirty air cooler can raise scavenge temperature but is not an ignition source in itself.
- 2
Which signs together most strongly suggest a scavenge fire on one unit?
Show answer
Answer: A. A fire in the scavenge space heats that unit's air charge, so its exhaust temperature and the scavenge temperature sensor both rise. Smoke or sparks from the scavenge drain and turbocharger surging may follow. Changes on all units at once point to a common cause, not a local fire.
- 3
You are the duty engineer and confirm a small scavenge fire on No. 4 unit. What should you do first?
Show answer
Answer: D. Reducing speed and cutting fuel to the unit removes heat, and extra cylinder oil helps the rings seal. Opening the doors feeds the fire with air and can injure people, and flooding the whole engine room with CO2 is far out of proportion to a small scavenge fire, which usually burns out this way; the scavenge space's own fixed extinguishing is used if it spreads.
- 4
SOLAS requires crankcase explosion relief valves on internal combustion engines having which of these?
Show answer
Answer: B. The relief valve requirement is based on bore (200 mm) or crankcase volume (0.6 m³). The 2,250 kW and 300 mm figures belong to the oil mist detection requirement, which is the classic mix-up.
- 5
Why must a crankcase explosion relief valve close again immediately after it lifts?
Show answer
Answer: B. After the primary explosion, gas cools and contracts, creating a partial vacuum that would draw in air. Air plus remaining oil mist plus a hot spot can give a second, often worse, explosion. Lube oil pressure is unrelated to the valve.
- 6
What is the purpose of the flame arrester fitted in a crankcase relief valve?
Show answer
Answer: D. The relief valve lets pressure out; the arrester gauze absorbs heat so flame does not leave with the gas and burn people standing nearby. The spring, not the arrester, holds the valve shut.
- 7
Under SOLAS, which engines need oil mist detectors, bearing temperature monitors or an equivalent device?
Show answer
Answer: A. Reg. 47.2 requires oil mist detectors, bearing temperature monitors or equivalent devices on engines of 2,250 kW and above or with cylinders of more than 300 mm bore. The 200 mm bore or 0.6 m³ crankcase figure is the Reg. 27 threshold for crankcase relief valves, which is the classic mix-up.
- 8
How does a typical oil mist detector judge the condition of the crankcase?
Show answer
Answer: C. Oil mist detectors use light (obscuration or scattering) to sense mist density in each compartment and alarm on a high level or a difference between compartments. Sump return temperature rises far too late to warn of a hot spot.
- 9
The oil mist detector alarms on No. 3 unit at sea. After informing the bridge and reducing speed, what is the key safety point?
Show answer
Answer: D. The danger is a crankcase explosion, so people must stay away from doors and relief valves. Opening early admits air to a hot spot. Lube oil circulation helps cool the bearings, so stopping it early is wrong unless the maker says so.
- 10
What usually provides the ignition source in a crankcase explosion?
Show answer
Answer: C. A hot spot first creates oil mist by vaporising oil, which condenses into a fine mist, and then ignites it. Detectors are designed to be safe in this atmosphere.
- 11
On a crosshead engine, what separates the crankcase from the scavenge space?
Show answer
Answer: B. The stuffing box scrapes dirty cylinder oil off the piston rod and stops it, and scavenge air, entering the crankcase. This keeps system oil clean and is why crosshead engines can burn residual fuel with separate cylinder lubrication.
- 12
What is the minimum starting air capacity class rules usually require for a reversible main engine?
Show answer
Answer: A. Classification rules set at least 12 consecutive starts, alternating ahead and astern, for a reversible engine without refilling the receivers. The figure of 6 applies to non-reversible engines, for example with a controllable pitch propeller, which is the usual trap.
- 13
While the engine is running, you notice the starting air branch pipe to No. 5 cylinder is much hotter than the others. What is the likely cause?
Show answer
Answer: A. A leaking cylinder starting valve lets hot gas into its own branch only, so only that pipe gets hot. This is dangerous because oil in the line can ignite. A passing main valve would affect the whole manifold, not one branch.
- 14
Why are flame arresters or bursting discs fitted in the starting air line near each cylinder starting valve?
Show answer
Answer: B. Lubricating oil carried over from the compressor coats the air pipes. Flame from a leaking valve can ignite it. The arrester or bursting disc limits the damage. Drains, not arresters, deal with water.
- 15
Why do you open the indicator cocks and turn the engine on air (blow through) before starting after a long stop?
Show answer
Answer: C. Liquid in a cylinder cannot be compressed and can cause serious damage when the piston rises. Blowing through with cocks open shows any leak from cooling water, fuel or oil. Warming is done with jacket water preheating, not air.
- 16
What does the turning gear interlock do?
Show answer
Answer: D. Starting with the turning gear engaged could wreck the gear and injure the person at it. The interlock blocks the start air until the gear is disengaged.
- 17
An indicator card has an area of 540 mm² and a length of 60 mm. The spring scale is 0.5 mm per bar. What is the mean indicated pressure?
Show answer
Answer: C. Mean height = 540 ÷ 60 = 9 mm. Pressure = 9 mm ÷ 0.5 mm per bar = 18 bar. Taking 9 bar forgets the spring scale; 4.5 bar multiplies by the scale instead of dividing.
- 18
A six-cylinder two-stroke engine has a bore of 500 mm and a stroke of 2,000 mm and runs at 100 rpm. Mean indicated pressure is 18 bar. What is the total indicated power, to the nearest 10 kW?
Show answer
Answer: A. Indicated power = pmi × A × L × n × cylinders, with n in revolutions per second because a two-stroke fires every revolution: 1,800 kPa × 0.1963 m² × 2.0 m × 1.667 rev/s × 6 ≈ 7,070 kW. Using n/2 as for a four-stroke gives 3,530 kW, and 1,180 kW is one cylinder only.
- 19
What is a 'draw card' (out-of-phase card) mainly used to check?
Show answer
Answer: D. Pulling the card by hand, or with the drive 90 degrees out of phase, spreads out the region around top dead centre. You can then see compression, the start of combustion and the peak pressure clearly. It gives no direct information on valve lift or alignment.
- 20
One unit shows normal compression pressure, low peak pressure and high exhaust temperature. Which fault fits best?
Show answer
Answer: B. Normal compression means air is not being lost, so rings and exhaust valve are probably fine. Low peak pressure with high exhaust temperature means the fuel burns late, into the expansion stroke. A fouled air filter would affect all units.
- 21
One unit shows low compression pressure and low peak pressure with normal injection timing. What is the most likely cause?
Show answer
Answer: B. If compression pressure is low, air is escaping before combustion. Peak pressure falls with it. Late injection lowers peak pressure but leaves compression pressure normal, which is the trap.
- 22
What does variable injection timing (VIT) do on a mechanically controlled engine?
Show answer
Answer: D. VIT moves the start of injection earlier in the part-load range so maximum pressure stays near its design value, which lowers fuel consumption. Above a set load it retards timing to protect against excess pressure. Fuel quantity is the governor's job.
- 23
A main engine develops 10,000 kW with a specific fuel oil consumption of 170 g/kWh. How much fuel does it burn in 24 hours?
Show answer
Answer: A. 170 g/kWh × 10,000 kW = 1,700,000 g per hour = 1.7 t/h. 1.7 × 24 = 40.8 t per day. 1.7 tonnes is only one hour's burn.
- 24
Propeller pitch is 5 m and the engine turns at 100 rpm. The ship's speed is 15 knots. What is the apparent slip, to one decimal place?
Show answer
Answer: C. Engine distance per hour = 5 × 100 × 60 = 30,000 m = 30,000 ÷ 1,852 = 16.20 nm. Slip = (16.20 − 15) ÷ 16.20 × 100 = 7.4%. Dividing by the ship's speed instead of the engine distance gives 8.0%.
- 25
What is turbocharger surging?
Show answer
Answer: D. Surging happens when the compressor operating point crosses the surge line: pressure ratio too high for the air flow. It makes a barking or roaring noise. Common causes are fouled turbine nozzles, fouled scavenge ports or a dirty air cooler, and sudden load changes.
- 26
Why do auxiliary blowers run at low engine load on a slow-speed two-stroke engine?
Show answer
Answer: C. At low load there is too little exhaust energy to drive the turbocharger hard enough. The electric blowers make up the scavenge air so combustion stays clean. They have nothing to do with the crankcase, which is sealed from the scavenge space.
- 27
Modern slow-speed two-stroke engines mostly use which scavenging method?
Show answer
Answer: B. Uniflow scavenging sweeps air in one direction from bottom to top, giving better scavenging of long-stroke cylinders. Loop and cross scavenging were used on older designs.
- 28
What closes the exhaust valve on many modern slow-speed engines?
Show answer
Answer: A. Hydraulic oil opens the valve and an air spring closes it. Air springs avoid steel spring fatigue. Cylinder gas pressure helps hold the valve on its seat during combustion, but it cannot close an open valve during the exhaust stroke.
- 29
On an electronically controlled engine without a camshaft, how are fuel injection and exhaust valve opening usually actuated?
Show answer
Answer: A. Electronic engines use servo oil or a common rail with electronically controlled valves, which lets timing change freely with load. There is no mechanical camshaft to drive.
- 30
What causes cold corrosion of cylinder liners?
Show answer
Answer: B. Sulphur in fuel forms sulphur oxides, which with water vapour form sulphuric acid. If the liner wall is too cold, acid condenses and attacks the surface. Raising jacket water temperature within limits and using the right cylinder oil BN reduce it.
- 31
The ship changes from high-sulphur fuel to 0.50% sulphur fuel for a long voyage. What should you do with cylinder lubrication?
Show answer
Answer: C. High BN additive left unused by low-sulphur fuel forms hard calcium deposits that polish the bore and cause scuffing. Matching BN to sulphur content is the fix. Cylinder oil is still needed for lubrication whatever the sulphur level.
- 32
Jacket cooling water pressure is fluctuating and gas is venting from the expansion tank. What is the likely cause?
Show answer
Answer: D. Combustion gas at high pressure enters the cooling water through a crack, forming gas pockets that make pressure fluctuate and vent at the tank. A lube oil cooler leak would show oil, not gas.
- 33
What do crankshaft deflection readings mainly show?
Show answer
Answer: C. A dial gauge between the crank webs shows opening and closing as the shaft turns. Large values mean the main bearings are not in line. Torsional vibration needs a torsiograph, not a web gauge.
- 34
Why must the engine not run continuously in the barred speed range?
Show answer
Answer: A. The barred range is set from torsional vibration calculations and measurements. Passing through quickly is allowed; staying there can crack the crankshaft or intermediate shaft. It is not a turbocharger limit.
- 35
What can be checked through the scavenge ports during a scavenge inspection?
Show answer
Answer: D. Turning the piston past the ports lets you see the rings, the lower liner surface and the piston skirt and crown edge. The exhaust valve seat is in the cover and needs the valve removed or a boroscope from above.
- 36
A piston crown is found burned in one area. What is the most likely cause?
Show answer
Answer: B. A worn or dribbling nozzle lets fuel jets hit the crown and burn away metal locally. Poor piston cooling can also cause it, but low scavenge or jacket temperatures do not; check the injector first.
- 37
The engine turns on air at normal speed but does not fire. Starting air pressure is normal. What is the most likely cause?
Show answer
Answer: B. If the engine turns at normal starting speed, the air system is working. Failure to fire then points to fuel: no fuel, air in the lines, a fuel limiter or an active shutdown. An engaged turning gear would stop the engine turning at all.
- 38
A marine diesel engine of more than 130 kW is fitted on a ship. Which document shows that this engine meets the NOx limits of MARPOL Annex VI?
Show answer
Answer: D. Each diesel engine above 130 kW covered by Reg. 13 needs an Engine International Air Pollution Prevention (EIAPP) certificate, with its NOx Technical File kept on board for survey. The IAPP certificate covers the ship and lists its engines, but it does not replace the engine's own EIAPP certificate.
- 39
What is the role of the overspeed trip on a main engine?
Show answer
Answer: C. The overspeed trip is a separate safety device so a failed governor cannot let the engine run away. Limiting fuel by scavenge pressure is the governor's charge air limiter, a different function.
- 40
A slow-speed two-stroke engine has a stroke of 2,000 mm and runs at 100 rpm. Its mean piston speed is about:
Show answer
Answer: A. The piston travels two strokes per revolution: 2 × 2.0 m × 100 ÷ 60 = 6.7 m/s. 3.3 m/s counts only one stroke per revolution; 200 m/s forgets to convert minutes to seconds.
Reading answers is not the same as saying them. Our AI voice examiner asks these out loud, listens to your answer, asks the follow-up and marks you against the rule. Join early access or try the free timed mock oral drill.
Frequently asked questions
Are these the questions asked in the MEO Class 4 exam?
No. We wrote every question ourselves around the published syllabus and the regulations. They are the kind of question you should expect, but they are not taken from any exam paper.
What is the most common main engine oral question?
Scavenge fire and crankcase explosion come up very often, because both are safety-critical and test your actions in order. Expect to be asked for causes, signs, immediate actions and prevention, and then a follow-up on why you must not open doors early.
What is the difference between a scavenge fire and a crankcase explosion?
A scavenge fire burns oil and carbon in the scavenge air space above the piston rod stuffing box. A crankcase explosion is the ignition of oil mist inside the crankcase, usually from a hot spot such as an overheated bearing. They are separate spaces on a crosshead engine.
Why must crankcase relief valves close after opening?
If the valve stayed open, fresh air would rush into the hot crankcase after the first explosion. That air can form a new explosive mixture and cause a second, more violent explosion. The valve must relieve pressure and then seal.
How do you calculate mean indicated pressure from an indicator card?
Measure the card area with a planimeter, divide by the card length to get the mean height, then divide by the spring scale (mm per bar). The result is the mean indicated pressure in bar.
What does a low compression pressure on one unit tell you?
Air is being lost before combustion. Common causes are a leaking exhaust valve, broken or stuck piston rings, or a worn liner. Low compression pressure also lowers the peak pressure.
How many starts must a reversible main engine get from its air receivers?
Classification rules generally require at least 12 consecutive starts, alternating ahead and astern, without refilling the receivers. Check the rules of your ship's class society for the exact wording.
Why is cylinder oil base number important?
The base number neutralises sulphuric acid formed from fuel sulphur. Too low a BN for the fuel causes corrosive wear; too high a BN with low-sulphur fuel leaves hard deposits and polishes the liner. Match it to the fuel as the maker advises.
What is a barred speed range?
It is a band of engine speed where torsional vibration of the shafting is at resonance. The engine may pass through it but must not run in it continuously. It is marked on the tachometer and in the engine documents.
How long should I wait before opening the crankcase after an oil mist alarm?
Follow the engine maker's instructions for the cooling period. The aim is to let any hot spot cool below the point where it could re-ignite oil mist when air enters. Keep people away from the relief valves meanwhile.
Is this set useful for CES engine tests?
Yes, the topics overlap with company screening tests for engineers. For test-style practice, also use our CES engine practice set and read the CES for engineers guide.
Sources 1 document
Each number in the text links to the source below. Labels show the type of source; see our editorial policy.
- Official IMO Resolution MEPC.176(58), revised MARPOL Annex VI, Reg. 14.1 and 14.4 · 10 October 2008