NautemyCoC orals · exams · job testsEarly access
Oral topic46 min readJump to 38 questions

Ship stability oral exam: questions, model answers and the numbers examiners expect

Ship stability orals test whether you can keep a ship upright with real numbers: GM, free surface, list versus loll, load lines, the 2008 IS Code criteria (0.055, 0.09, 0.03 m-rad, GZ 0.2 m at 30°, GM 0.15 m) and grain rules. Below: 38 model answers, worked calculations and the tables to learn.

Minimum GM (IS Code)
0.15 m
Minimum GM (grain)
0.30 m
Questions on this page
36 oral, core to trap
On this page
  1. Key facts
  2. What do examiners ask about ship stability at each rank?
  3. What are the 2008 IS Code intact stability criteria?
  4. What are the grain stability criteria under the International Grain Code?
  5. Which stability formulas should you know by heart for the oral?
  6. How do you tell a list from an angle of loll?
  7. How should you structure a stability answer in the oral?
  8. How do you work the stability calculations examiners ask for?
  9. How do you talk through a stability scenario step by step?
  10. What separates a weak stability answer from a strong one?
  11. Which stability scenarios come up in orals?
  12. What are the most common stability mistakes in orals?
  13. What has changed recently in stability rules?
  14. What should you read to revise ship stability?
  15. Where is ship stability examined and how can you practise?
  16. 38 practice questions
  17. Frequently asked questions
  18. Sources

Key facts

Topic
Ship stability (STCW function: controlling the operation of the ship)
Examined at
2nd mate / OOW, chief mate, master orals
Main code
2008 IS Code, Part A mandatory[1]
Mandatory from
1 July 2010 (ships 24 m+ built on or after that date)[2]
Minimum GM (IS Code)
0.15 m
Minimum GM (grain)
0.30 m
Key areas
0.055 / 0.09 / 0.03 m-rad
Questions on this page
36 oral, core to trap

Checked 13 November 2026. Fees and rules change: confirm with the authority before you book.

What do examiners ask about ship stability at each rank?

Examiners at every level ask stability, but the depth rises with rank: an OOW must explain GM, free surface and list, a chief mate must calculate and apply the IS Code and grain criteria, and a master must make decisions with them.

At the 2nd mate oral in India and the MCA OOW deck oral, stability sits inside the operational level function "controlling the operation of the ship". You are expected to read the stability booklet, explain the basic terms with a sketch, and know what you would do on watch if the ship took a list. At the chief mate oral and the MCA chief mate oral the questions move to the management level: GZ curves, the weather criterion, grain, dry docking, damage stability and the loading computer. At the master oral and the MCA master oral the examiner usually gives you a situation and asks for your decision and who you would inform.

Stability also appears in the written papers (MMD written exams, SQA written exams) as calculations. The oral checks that you understand what the numbers mean. If you need to tell the two oral levels apart, read 2nd mate vs chief mate oral.

Depth of stability questions by rank (our summary of the STCW competence tables and typical oral practice)
Rank / examWhat you must showTypical questions
2nd mate / OOW (operational level)Definitions with a sketch; GM, GZ, KG, KM; free surface; list vs loll; load line marks; FWA/DWA; reading the stability booklet; effect of ballast and bunkers"Define GM." "What is free surface effect?" "Ship is listed on watch, what do you do?"
Chief mate (management level)IS Code criteria with numbers; GZ curve analysis; weather criterion; trim and draught calculations; dry docking; heavy lifts; grain and timber criteria; loading computer checks; damage stability basics"State the IS Code criteria." "Explain the critical period." "How do you prove grain stability?"
Master (management level)Decisions and responsibility: heavy weather, parametric roll, flooding, loll at sea, overloading and load line law, dealing with class, flag and charterers"Your ship develops a loll at sea, what do you do?" "Charterer wants more cargo than the load line allows."

What are the 2008 IS Code intact stability criteria?

The 2008 IS Code sets six general criteria in Part A 2.2 (areas, GZ and GM) plus the severe wind and rolling (weather) criterion in Part A 2.3, and these are the numbers examiners ask most often.

The Code was adopted by IMO resolution MSC.267(85) and its Part A became mandatory through SOLAS and the 1988 Load Lines Protocol from 1 July 2010[1]. Ships of 24 m and over built on or after that date must at least meet Part A[2]. Part B is recommendatory guidance: free surface, icing, the inclining test, operational advice in heavy weather. Learn the table below exactly. Also say "after correction for free surface" every time you quote a GM value. For the Load Line side, see our SOLAS oral topic and ship construction pages.

2008 IS Code Part A: general and special criteria (values from the Code text)
CriterionValueIS Code reference
Area under GZ curve up to 30°Not less than 0.055 m-radPart A 2.2.1
Area up to 40° (or down-flooding angle if less)Not less than 0.09 m-radPart A 2.2.1
Area between 30° and 40° (or 30° and down-flooding angle)Not less than 0.03 m-radPart A 2.2.1
GZ at an angle of 30° or moreAt least 0.2 mPart A 2.2.2
Angle of maximum GZNot less than 25° (alternatives with Administration approval)Part A 2.2.3
Initial GM0Not less than 0.15 mPart A 2.2.4
Weather criterion: steady wind heel θ0Not more than 16° or 80% of deck edge immersion angle, whichever is lessPart A 2.3.1.2
Weather criterion: wind pressure and gustP = 504 Pa; gust lever lw2 = 1.5 × lw1Part A 2.3.2
Weather criterion: energy balanceArea b ≥ area a; θ2 = least of down-flooding angle, 50°, or second interceptPart A 2.3.1.4
Passenger ships: crowding and turningHeel not more than 10° in each casePart A 3.1
Timber deck cargo (alternative criteria)Area to 40° ≥ 0.08 m-rad; max GZ ≥ 0.25 m; GM ≥ 0.1 m throughout the voyagePart A 3.3.2
Free surfaceAccount for it in all loading conditions; tanks ≥ 98% full treated as nominally fullPart A 2.1.2; Part B 3.1.2

What are the grain stability criteria under the International Grain Code?

A ship carrying bulk grain must show, after allowing for an assumed grain shift, a heel of not more than 12° (or deck edge immersion if less, for ships built from 1994), a residual area of 0.075 m-rad and a GM of 0.30 m.

The International Grain Code was adopted by resolution MSC.23(59) and applies through SOLAS Chapter VI Part C[3]. Each ship needs a document of authorization and a grain loading manual. The chief mate prepares the grain stability calculation (often on an approved form) and the master may have to show it to the port state before loading. A recent amendment adds an optional fourth loading condition that must be in the approved manual and loading computer before use[4]. For the cargo side of grain (trimming, securing, fumigation) see cargo work.

International Grain Code: numbers to know
ItemRequirementReference
Heel due to grain shiftNot more than 12°, or for ships built on or after 1 Jan 1994 the deck edge immersion angle, whichever is lessA 7.1.1
Residual (net) areaNot less than 0.075 m-rad, up to the angle of maximum difference, 40° or flooding angle (least)A 7.1.2
Initial GM (after free surface)Not less than 0.30 mA 7.1.3
Heeling arm at 40°λ40 = 0.8 × λ0Figure A 7
Ship upright before sailingMaster must ensure the ship is upright after loadingA 7.3
Filled compartment, trimmed (voids allowed for)Heeling moment × 1.06Part B (assumed heeling moments)
Partly filled compartmentHeeling moment × 1.12Part B (assumed heeling moments)
No document of authorization (A 9)Grain ≤ one third of deadweight; GM ≥ 0.3 m or formula value; other conditionsA 9.1

Which stability formulas should you know by heart for the oral?

You need about a dozen formulas, and the examiner will want you to explain each one with a sketch rather than recite it. Know what every symbol means and in what units.

Draw the midship section with K, B, G, M and Z marked before you answer any GM or GZ question. It shows the examiner you understand the geometry. Practise the arithmetic in our ship stability MCQ bank and the practice test.

Core stability formulas
QuantityFormulaUse
Metacentric heightGM = KM − KGInitial stability
Metacentric radiusBM = I / V (I = second moment of waterplane area, V = volume of displacement)Why beam matters so much
Righting lever (small angles)GZ = GM × sin θUp to about 10–15°
Righting lever (large angles)GZ = KN − KG × sin θFrom cross curves
Shift of GGG1 = w × d / ΔLoading, discharging, shifting weight
Angle of listtan θ = GG1 / GMOff-centre weight
Free surface (rectangular tank)FSM = l × b³ / 12 × ρ; virtual rise = FSM / ΔSlack tanks
Angle of loll (wall-sided)tan θ = √(2 × GM / BM), GM taken as its magnitudeNegative GM
TPCTPC = A(wp) × ρ / 100Sinkage
Change of trimTrimming moment about LCF / MCTCFinal drafts
Fresh water allowanceFWA (mm) = Δ / (4 × TPC)Load line in fresh water
Dock water allowanceDWA = FWA × (1025 − ρ) / 25Load line in dock water
Dry-dock upthrustP = MCTC × change of trim / distance of LCF from aftCritical period
Inclining testGM = w × d / (Δ × tan θ)Lightship KG

How do you tell a list from an angle of loll?

A list comes from an off-centre G with positive GM; loll comes from a negative GM with G on the centreline. They are corrected in opposite ways, so examiners at every rank test this.

The danger is shifting weight "to the high side" on a lolling ship. On a ship with negative GM, that makes her flop to the other side, often further. Always find the cause first: soundings, cargo plan, recent ballast or bunkering, and a check for water ingress.

List vs loll
ListLoll
CauseG off the centreline (GG1)G above M (negative initial GM)
GMPositiveNegative when upright
BehaviourLies to one side only; rolls about the listed angleMay flop to either side; long, lazy roll
Typical triggersUneven cargo, tanks or bunkers; crane liftConsumption from DB tanks, water in timber deck cargo, ice, free surface
CorrectionMove or add weight on the high sideLower G: fill low-side divided DB tank first, then the other; remove free surface and top weight
Do notIgnore free surface while correctingShift weight across to the high side

How should you structure a stability answer in the oral?

Start with the definition, draw a sketch, give the rule or code with its number, then say what you would do on board. That order works for almost every stability question.

  1. Define in one sentence ("GM is the distance between G and M").
  2. Sketch the section or the GZ curve. Examiners at Indian MMD and MCA orals often hand you paper for this.
  3. Quote the rule with numbers and reference ("IS Code Part A 2.2.4, GM at least 0.15 m after free surface correction").
  4. Apply it: what you check, what you do, who you inform (master, chief engineer, company).
  5. Stop. Let the examiner ask the follow-up. Long speeches give more chances to say something wrong.

If you do not know a number, say so and explain where you would find it (stability booklet, IS Code, Grain Code). Guessing a number on a safety-critical topic is the fastest way to fail. Our guide to answering oral questions and what oral examiners look for cover this in more detail. You can rehearse out loud with the mock oral drill.

How do you work the stability calculations examiners ask for?

Work every stability sum in the same order: new displacement, new KG, free surface, fluid GM, then the list, loll or trim. The five worked examples below use round numbers you can redo on paper in the oral.

The examiner rarely wants the third decimal place. They want to see that you take moments about the keel, that you correct for free surface before you use GM, and that you know when a formula stops being valid. Practise the arithmetic in the ship stability MCQ bank.

Example 1: loading an off-centre weight (list). Displacement 12,000 t, KG 7.40 m, KM 8.20 m (assume KM does not change for this small weight). You load 150 t at Kg 10.0 m, 6.0 m to starboard of the centreline.

  • New displacement = 12,000 + 150 = 12,150 t.
  • New KG = (12,000 × 7.40 + 150 × 10.0) / 12,150 = (88,800 + 1,500) / 12,150 = 90,300 / 12,150 = 7.432 m.
  • Solid GM = 8.20 − 7.432 = 0.768 m.
  • Horizontal shift of G: GG1 = w × d / Δ = 150 × 6.0 / 12,150 = 0.074 m.
  • List: tan θ = GG1 / GM = 0.074 / 0.768 = 0.0965, so θ ≈ 5.5° to starboard.

Example 2: the same ship with a slack tank (free surface). A double bottom tank 15 m long and 10 m wide is part full of fuel of relative density 0.95.

  • FSM = l × b³ / 12 × ρ = 15 × 1,000 / 12 × 0.95 = 1,187.5 t-m.
  • Virtual rise of G = FSM / Δ = 1,187.5 / 12,150 = 0.098 m.
  • Fluid GM = 0.768 − 0.098 = 0.670 m, and the list from Example 1 grows to tan θ = 0.074 / 0.670, θ ≈ 6.3°.
  • If the same tank had a centreline longitudinal bulkhead, each half has b = 5 m, so each FSM is one eighth of the undivided value and the pair together is one quarter: 296.9 t-m, a virtual rise of only 0.024 m. This is why divided tanks are used and why you never fill both halves "together through one valve".

Example 3: angle of loll. A wall-sided ship has an upright GM of −0.10 m and BM 4.0 m.

  • tan θ = √(2 × GM / BM) = √(2 × 0.10 / 4.0) = √0.05 = 0.224, so θ ≈ 12.6°.
  • Say aloud that the formula holds only for a wall-sided form and only near the loll angle, and that the cure is to lower G, not to shift weight across.

Example 4: heavy lift with the ship's crane. Displacement before the lift 9,000 t, KG 7.00 m, KM 7.90 m. A 60 t lift is taken from the quay. The moment it leaves the quay its weight acts at the crane head, 25 m above the keel, with an outreach of 15 m from the centreline.

  • New KG = (9,000 × 7.00 + 60 × 25) / 9,060 = (63,000 + 1,500) / 9,060 = 7.119 m.
  • GM = 7.90 − 7.119 = 0.781 m (before any free surface).
  • GG1 = 60 × 15 / 9,060 = 0.099 m, so tan θ = 0.099 / 0.781, θ ≈ 7.3° maximum list with the load at full outreach.
  • The two points the examiner wants: the weight acts at the head of the crane from the moment the load lifts, and the maximum list happens at maximum outreach, so check it before lifting, not after.

Example 5: the critical period in dry dock. MCTC 180 t-m per cm, trim 1.20 m (120 cm) by the stern, distance of the after end of the keel from the LCF 70 m, displacement 12,000 t, KM 8.20 m.

  • Upthrust at the stern when it lands on the blocks: P = MCTC × t / l = 180 × 120 / 70 = 308.6 t.
  • Virtual loss of GM = P × KM / Δ = 308.6 × 8.20 / 12,000 = 0.211 m.
  • If the ship's fluid GM was 0.25 m, she would be left with only about 0.04 m just before she settles on the blocks fore and aft. That is the reason for small trim, slack tanks pressed up or emptied, and no weight moved during the critical period.

Example 6: fresh water and dock water allowance. Summer displacement 20,000 t, TPC 30.

  • FWA = Δ / (4 × TPC) = 20,000 / 120 = 166.7 mm (about 167 mm).
  • In dock water of density 1.010 t/m³: DWA = FWA × (1,025 − 1,010) / 25 = 166.7 × 15 / 25 = 100 mm. The summer load line may be submerged by up to 100 mm in that dock water, so that she rises to the mark in salt water.
Which stability formula to use, and when it fails
SituationFormulaValid whenCommon slip
Initial stability, small heelGZ = GM × sin θUp to about 10–15° while M stays fixedUsing it at 30° to "check" the IS Code criteria
Large anglesGZ = KN − KG × sin θAny angle, using cross curves (KN)Forgetting free surface correction to KG
Weight added, removed or shiftedGG1 = w × d / Δ (Δ after the change)Always, taking moments about the keel and centrelineUsing the old displacement after loading
List from an off-centre Gtan θ = GG1 / GMPositive GM, small anglesUsing solid GM instead of fluid GM
Slack rectangular tankFSM = l × b³ / 12 × ρ; rise = FSM / ΔTank not pressed up and not nearly emptySaying the quantity of liquid matters
Angle of lolltan θ = √(2 × GM / BM)Wall-sided form, near the loll angleTreating the loll as a list
Dry-dock upthrustP = MCTC × t / lTrimmed by the stern, stern landing firstUsing the distance from midships instead of from the LCF
Load line in fresh or dock waterFWA = Δ / (4 × TPC); DWA = FWA × (1,025 − ρ) / 25Summer displacement and TPC from the bookletApplying the full FWA in brackish dock water

How do you talk through a stability scenario step by step?

Use five steps for every stability scenario: situation, assessment, rule, action, report. The three walk-throughs below show the level of detail a chief mate or master examiner expects.

Walk-through 1: an unexplained list at night

Situation. You are OOW on a loaded bulk carrier at 0200. The inclinometer shows 4° to port. An hour ago it was upright. No cargo or ballast operation is planned.

Assessment. A list that arrives without a planned operation has three possible causes: a weight or liquid moved (a transfer, a leaking valve between tanks), water entering a space, or G has risen to give a small negative GM so the ship has lolled to one side. Note the roll: does she roll about 4° to port, or does she hang and flop?

Rule. The ship must keep the stability in her approved booklet, and the IS Code requires GM to be judged after free surface correction (Part A 2.2.4). On a bulk carrier, SOLAS Chapter XII water ingress alarms in the holds are the first instrument to check.

Action.

  1. Call the master as the standing orders require. Reduce speed if the sea is on the beam.
  2. Check the hold and ballast-tank water ingress alarms and bilge high-level alarms.
  3. Ask the engine room about any fuel transfer or ballast pump running, and check the valve status.
  4. Order soundings of all double bottom, wing and peak tanks, void spaces and hold bilges; compare with the last noon soundings.
  5. If soundings show a transfer: stop it and reverse it. If they show unexplained water: start the damage control plan and pumping. If nothing moved and the roll is long and lazy: treat it as loll and lower G (fill the low-side divided double bottom tank first).

Report. Inform the master of the cause and corrective action, log the times, soundings and actions, and, if water ingress is found, the master informs the company and considers emergency procedures.

Examiner's note: The panel listens for "soundings before ballast". Candidates who start pumping to the high side straight away fail, because if the cause is loll the ship flops further to the other side. The usual follow-up is "Soundings are normal and she rolls slowly. Now what?"

Walk-through 2: a timber carrier develops loll near the end of the voyage

Situation. You are chief mate on a timber carrier with deck cargo, 2 days from port. Heavy rain for 3 days. The ship lies 8° to starboard, then flops to 8° to port after a course alteration.

Assessment. Flopping from side to side with a slow roll means negative initial GM. Causes: fuel and water burned from double bottom tanks (weight removed from low down, G rises), rainwater absorbed by the deck cargo (weight added high up) and possible ice. The deck cargo also adds free surface if water is trapped.

Rule. For timber deck cargo, the IS Code alternative criteria (Part A 3.3.2) require GM of at least 0.1 m throughout the voyage, and the timber stability calculation must allow for water absorption and ice. The Code of Safe Practice for Ships Carrying Timber Deck Cargoes gives the operational guidance.

Action.

  1. Do not move weight across. Do not jettison cargo yet unless the master decides there is no alternative.
  2. Fill the empty double bottom tank on the low side first, one divided tank at a time, so the free surface is added on the side she already lies on. Then fill the opposite tank.
  3. Remove free surface: press up slack tanks or empty them.
  4. Reduce speed and choose a heading that keeps her steady while correcting.
  5. Recalculate with the loading computer or by hand and confirm a positive GM before resuming.

Report. Inform the master throughout; the master informs the company and records the event, the soundings and the calculation in the log.

Examiner's note: The strong answer says why the low side goes first. If you fill the high-side tank first, you add an off-centre weight on the high side while the new free surface cuts GM further, and the ship can flop over to the other side, often to a larger angle. Filling the low side first puts the weight low and on the side she already lies, so she cannot flop; as G comes down and GM turns positive she comes back towards upright, and you then fill the other side. A weak answer says "fill double bottom tanks" without saying which one first.

Walk-through 3: loading a heavy lift with the ship's own gear

Situation. You are chief mate. A 60 t transformer will be loaded with the ship's crane to the offshore side. Displacement 9,000 t, KG 7.00 m, KM 7.90 m, crane head 25 m above the keel, maximum outreach 15 m.

Assessment. Work out the worst case before lifting (Example 4 above): about 7.3° list at maximum outreach, with GM 0.78 m before free surface. Check the crane's safe working load at that outreach, the effect of the heel on the crane itself (many cranes have a maximum permitted heel) and the mooring lines.

Rule. The stability booklet and the crane's manufacturer limits apply; the lifting appliance must be certified and inspected under SOLAS II-1/3-13, in force since 1 January 2026[5].

Action.

  1. Press up or empty slack tanks to remove free surface; consider ballasting the opposite side to counter-list before the lift, by the amount calculated.
  2. Brief the crane driver, deck crew and signaller; clear the area under the load; tend moorings.
  3. Lift slowly a few centimetres, stop, check the list against your calculation, then continue.
  4. Land the load, secure it, then remove the counter-ballast and recalculate the voyage stability with the new weight and its final position.

Report. Record the lift, ballast changes and final GM, and give the master the departure condition.

Examiner's note: The panel wants to hear "the weight acts at the crane head as soon as it leaves the quay". A strong candidate adds that the list is largest at full outreach and that a listing ship can push the crane beyond its own heel limit.

What separates a weak stability answer from a strong one?

A strong stability answer gives the definition, the number with its source, and what you would do on board, in that order. These examiner's notes show the difference on the questions candidates fumble most.

Examiner's note: "What is GM?" Weak answer: "It is the stability of the ship." Strong answer: "GM is the distance from G to M, so GM = KM − KG. It measures initial stability up to about 10–15°. The IS Code minimum is 0.15 m after free surface correction. On board I take KM from the hydrostatic tables at the present draught and KG from the loading condition." The strong answer gives the definition, the formula, the limit, the source and how it is used.

Examiner's note: "What is free surface effect?" Weak answer: "Water moving in a tank makes the ship unstable, so we keep tanks full." Strong answer: "A slack tank's liquid moves to the low side as the ship heels, which acts as a virtual rise of G equal to FSM ÷ displacement. FSM depends on the breadth cubed and the liquid density, not on the quantity. Divide tanks longitudinally, keep them pressed up or empty, and do not have many slack tanks at once."

Examiner's note: "The ship has a list. What do you do?" Weak answer: "Pump ballast to the other side." Strong answer: "First I find out whether it is a list or a loll: soundings, recent transfers, the type of roll and water ingress. Only for a list with positive GM do I add or move weight to the high side. For loll I lower G, starting with the low-side tank."

Examiner's note: "State the IS Code criteria." Weak answer: a list of numbers with no units or the 0.30 m grain GM mixed in. Strong answer: the six Part A 2.2 values with units (0.055, 0.09 and 0.03 m-rad; GZ 0.2 m at 30° or more; maximum GZ at not less than 25°; GM0 0.15 m), then "plus the weather criterion in 2.3, and every value after free surface correction".

Which stability scenarios come up in orals?

Scenario questions are where most marks are won or lost, because they test judgement, not memory. Expect the examiner to change one detail after your first answer.

  • Unexplained list on watch. Check cargo and tank soundings, ask the engine room about transfers, check bilge alarms and void spaces for flooding, then decide list or loll.
  • Loll after bunkers consumed on a timber carrier. Water absorption and fuel consumption from DB tanks raise G. Correct by filling the low-side divided DB tank first.
  • Heavy lift with ship's gear. Calculate the maximum list with G raised to the derrick head; remove free surface; tend moorings.
  • Entering dry dock. Keep trim small, give stability details to the dock master, avoid moving weights during the critical period.
  • Heavy weather on a container ship. Watch for parametric roll in head or following seas; alter course or speed (see meteorology and passage planning).
  • Flooding in a forward hold. Follow the damage control plan; trim and free surface; consider emergency procedures.
  • Ballast water exchange at sea. Sequential exchange changes stability, trim, bending moments and shear forces at each step; plan it with the ballast water management plan (see ballast water management).
  • Grain loading port asks for proof of stability. Show the document of authorization and grain calculation sheet.

What are the most common stability mistakes in orals?

The most common mistakes are mixing up list and loll, quoting GM without free surface correction, getting the IS Code numbers wrong and forgetting what you would actually do on board.

  • Wrong correction for loll. Saying "shift weight to the high side". This alone can fail a candidate.
  • Saying free surface depends on quantity. It depends on the breadth of the free surface (b³) and the liquid density, not on how much liquid is in the tank.
  • Mixing the criteria. 0.15 m is the IS Code minimum GM; 0.30 m is the grain minimum; 0.1 m is the timber alternative minimum. Do not swap them.
  • No sketch. Candidates who cannot draw K, B, G, M and Z usually cannot explain them either.
  • Ignoring the arrival condition. Stability gets worse as fuel and water are used from low tanks.
  • Trusting the loading computer blindly. Say how you check it (test conditions, draught comparison).
  • Saying "always" and "never" loosely. "A large GM is always safe" is a trap.
  • Answering a chief mate question with OOW depth. At management level, include planning, calculation and responsibility.

The why seafarers fail oral exams article lists more patterns across topics.

What has changed recently in stability rules?

The core criteria have not changed, but new equipment rules and guidance affect stability questions in 2026, mainly electronic inclinometers and second generation intact stability criteria.

  • Electronic inclinometers. From 1 January 2026, new container ships and bulk carriers of 3,000 GT and above must carry an electronic inclinometer or other means to determine, display and record roll motion[5]. Expect a chief mate examiner to ask why: roll data helps investigate container losses and heavy-weather damage.
  • Second generation intact stability criteria. IMO interim guidelines cover five dynamic failure modes (dead ship, excessive accelerations, pure loss of stability, parametric roll, surf-riding/broaching). They are for trial use, not mandatory[6].
  • Grain Code. An amendment adds an optional fourth loading condition[4].
  • Container loss reporting. Linked to stability and cargo securing: since 1 January 2026, masters must report lost containers without delay[7].

What should you read to revise ship stability?

Revise from the codes first, then one good textbook, then your own ship's stability booklet. Examiners like candidates who quote the code and relate it to a real ship.

  • International Code on Intact Stability, 2008 (IMO publication), Part A in full, Part B chapters on free surface, operational provisions and the inclining test.
  • International Grain Code (IMO publication), Part A 7 and A 9.
  • Load Lines consolidated edition (IMO), Annex I marks and zones.
  • SOLAS consolidated edition, Chapter II-1 (stability information, damage stability, damage control plans) and Chapter XII for bulk carriers.
  • Textbooks commonly used in Indian and UK preparation: Ship Stability for Masters and Mates (Barrass and Derrett), Merchant Ship Stability (Pursey), and the Ship Stability volumes by H. Subramaniam.
  • Your own ship's stability booklet and loading computer manual. Bring real examples to mind.

See our list of books for second mate orals and the 30-day oral preparation plan.

Where is ship stability examined and how can you practise?

Stability is examined at every deck oral in India and the UK, and in the written papers. Use the links below to see how each exam handles it, then practise.

Oral practice

38 oral questions with model answers

Read the question, answer it out loud as if the examiner is across the table, then open the model answer and mark yourself honestly.

–0/38 done
  1. 1
    CoreIS Code 2008 Part A 2.2.4

    Define metacentric height. Why does it matter to you as OOW?

    Model answer points
    • GM is the vertical distance between the centre of gravity G and the transverse metacentre M: GM = KM − KG. See metacentric height.
    • For small angles of heel (up to about 10–15°) the righting lever is GZ = GM × sin θ, so GM is the measure of initial stability.
    • Positive GM: G below M, the ship returns upright. Zero GM: neutral. Negative GM: the ship heels until it reaches an angle of loll.
    • Under the 2008 IS Code the initial GM must be at least 0.15 m, after free surface correction.
    • As OOW you care because ballast, fuel and water changes, ice, and deck cargo all move G. A long, slow, lazy roll is a warning sign of low GM.
    The examiner may follow up with
    • How do you find KM on board?
    • What is the difference between fluid GM and solid GM?
    How did you do?
  2. 2
    CoreIS Code 2008 Part A 2.2

    What is the righting lever GZ and the righting moment?

    Model answer points
    • GZ is the horizontal distance between the line of action of weight through G and the line of action of buoyancy through the new centre of buoyancy B1, when the ship is heeled.
    • Righting moment = displacement × GZ (tonne-metres). This is the moment that brings the ship back upright.
    • At small angles GZ = GM sin θ. At large angles you must take GZ from the cross curves (KN curves): GZ = KN − KG sin θ.
    • GZ depends on hull form (beam, freeboard) and on KG. You control KG; the hull form is fixed.
    The examiner may follow up with
    • Why can you not use GM sin θ at 30°?
    • Where do KN values come from?
    How did you do?
  3. 3
    CoreIS Code 2008 Part A 2.1.2; Part B 3.1

    What is free surface effect and how do you reduce it?

    Model answer points
    • A slack tank lets liquid move to the low side when the ship heels. The liquid's centre of gravity moves, which acts as a virtual rise of G. See free surface effect.
    • Virtual rise of G = free surface moment / displacement. For a rectangular tank, FSM = (l × b³ / 12) × density of the liquid.
    • It depends on the breadth of the free surface (b cubed), not on the amount of liquid in the tank.
    • Dividing a tank with longitudinal bulkheads into n equal parts reduces the effect to 1/n² of the original.
    • Reduce it by keeping tanks pressed up or empty, having as few slack tanks as possible at one time, and using one pair of tanks at a time when transferring.
    • The IS Code says free surface must be accounted for whenever a tank is filled below 98%.
    The examiner may follow up with
    • Why does depth of liquid not matter?
    • Which tanks do you assume slack in the stability calculation?
    How did you do?
  4. 4
    CoreIS Code 2008 Part A 2.3.4 (rolling period formula)

    Explain the difference between a stiff ship and a tender ship.

    Model answer points
    • Stiff: large GM. Short, quick, jerky roll period. Heavy racking stress, discomfort, risk of cargo and lashings failing, damage to deck cargo.
    • Tender: small GM. Long, slow roll period. Comfortable, but little reserve of stability; a gust or cargo shift can give a large heel.
    • Roll period is roughly inversely proportional to the square root of GM. The IS Code gives an approximate formula T = 2CB/√GM.
    • Neither extreme is good. Aim for a moderate GM that meets all criteria and suits the cargo (for example, container lashing limits, grain criteria).
    The examiner may follow up with
    • How would you check GM at sea using roll period?
    • What is synchronous rolling?
    How did you do?
  5. 5
    CoreInternational Convention on Load Lines 1966/88, Annex I Regs 4–8

    Name the marks of the load line and say what each one means.

    Model answer points
    • Deck line and the load line disc (Plimsoll mark) with a horizontal line through its centre, at the level of the summer load line.
    • S Summer, W Winter, T Tropical, F Fresh water (summer), TF Tropical fresh, WNA Winter North Atlantic (only for ships not over 100 m).
    • Winter is 1/48 of the summer draught below S; Tropical is 1/48 above S.
    • The upper edge of each line is the mark. Timber ships may also carry timber load lines (prefix L).
    • The marks show the maximum draught allowed in each zone and season. Overloading is an offence and a stability and strength risk.
    The examiner may follow up with
    • What is fresh water allowance?
    • Who decides the zones and seasons?
    How did you do?
  6. 6
    CoreInternational Convention on Load Lines 1966/88, Art. 12; Annex I Reg. 40

    What is the fresh water allowance (FWA) and the dock water allowance (DWA)?

    Model answer points
    • FWA is the number of millimetres by which the mean draught changes when a ship moves from salt water (1.025 t/m³) to fresh water (1.000 t/m³) at the summer displacement.
    • FWA (mm) = summer displacement / (4 × TPC), both at the summer load waterline in salt water. It is shown on the International Load Line Certificate.
    • DWA is the same allowance for dock water of density between 1.000 and 1.025: DWA = FWA × (1025 − ρ dock) / 25.
    • So you may load until the load line is submerged by the DWA in the dock, because the ship will rise when it reaches sea water.
    • Always measure dock water density with a hydrometer at several depths and both sides before final loading.
    The examiner may follow up with
    • Where on the hull is FWA marked?
    • Why must you also think about the voyage to the first zone change?
    How did you do?
  7. 7
    CoreShip stability booklet / hydrostatic particulars (SOLAS Ch. II-1 Reg. 5-1)

    What is TPC and MCTC? How do you use them?

    Model answer points
    • TPC (tonnes per centimetre immersion) = waterplane area × density / 100. It tells you how many tonnes change the mean draught by 1 cm.
    • MCTC (moment to change trim one centimetre) = Δ × GML / (100 × L). It tells you the trimming moment needed to change trim by 1 cm.
    • Change of trim (cm) = trimming moment about the LCF / MCTC.
    • Both come from the hydrostatic tables for the ship's draught and density.
    • You use them for loading small parcels, ballast changes, final trim and dry-dock calculations.
    The examiner may follow up with
    • Why is trim calculated about the LCF, not midships?
    • What happens to TPC in fresh water?
    How did you do?
  8. 8
    CoreSOLAS Ch. II-1 Reg. 5-1; IS Code 2008 Part A 2.1.6–2.1.7

    What information must the stability booklet give the master?

    Model answer points
    • SOLAS requires the master to be supplied with stability information so he can obtain accurate guidance on the ship's stability under varying conditions of service.
    • Typically: hydrostatic tables, cross curves (KN), tank capacities with centres of gravity and free surface moments, lightship particulars from the inclining test, worked loading conditions, limiting KG or minimum GM curves, and the criteria the ship must meet.
    • Under the IS Code, minimum GM or maximum KG curves must cover the full range of operational trims, or the master must check the actual trim condition.
    • Where an approved loading computer (stability instrument) is used, it is a supplement to the booklet, not a replacement.
    The examiner may follow up with
    • How do you test the loading computer on board?
    • What is a limiting KG curve?
    How did you do?
  9. 9
    CoreBasic stability principles; SOLAS Ch. II-1 Reg. 5-1 stability information

    How does a ship take up a list, and how do you calculate it?

    Model answer points
    • A list is a heel caused by G moving off the centreline (G1), with a positive GM. The ship lies at the angle where B is under G1.
    • tan θ = GG1 / GM, where GG1 = (weight × transverse distance) / displacement.
    • Causes: off-centre cargo or ballast, uneven bunkers, a crane lifting over the side, free surface and liquid shifting.
    • Correct by moving or adding weight to the high side, after making sure the GM is positive.
    The examiner may follow up with
    • How do you know it is a list and not loll?
    • How does a heavy lift with the ship's gear affect list?
    How did you do?
  10. 10
    CoreBasic stability principles

    What is an angle of loll? How is it different from a list?

    Model answer points
    • Loll happens when initial GM is negative. The ship heels until B moves out far enough that G and M coincide at that angle. GZ is zero there, and the ship is in neutral equilibrium.
    • The ship may flop from one side to the other, and it hangs at about the same angle each side. The roll period is long and the ship feels "dead".
    • A list is caused by an off-centre G with positive GM; the ship lies to one side only.
    • For a wall-sided ship: tan θ (loll) = √(2 × GM / BM), using the magnitude of the negative GM.
    • Correcting loll and list is done in opposite ways, so identifying which one you have is the first question every examiner asks.
    The examiner may follow up with
    • How do you correct a loll?
    • What causes a loll on a log carrier?
    How did you do?
  11. 11
    CoreIS Code 2008 Part A 2.1; Part B 3.1

    Why does a ship's GM change during a voyage?

    Model answer points
    • Consumption of fuel, fresh water and stores, usually from double bottom tanks, raises G.
    • New slack tanks add free surface effect.
    • Timber deck cargo absorbs water, and ice forms on decks and superstructures in cold areas, both raising G.
    • Ballast taken or discharged for trim or ballast water exchange changes G and free surface.
    • The arrival condition is often the worst condition, so the voyage plan must check stability at departure, during the voyage and at arrival.
    The examiner may follow up with
    • Which condition in the booklet do you check most carefully?
    • How do you allow for icing?
    How did you do?
  12. 12
    CoreShip hydrostatic data; trim and draught calculation (stability booklet)

    What is the trim and how do you calculate the final drafts after loading?

    Model answer points
    • Trim is the difference between the forward and aft draughts. By the stern when the aft draught is greater.
    • Steps: find the mean draught change from weight/TPC (bodily sinkage), then the trim change = (weight × distance from LCF) / MCTC.
    • Divide the trim change between forward and aft in proportion to the LCF position: change of draught aft = change of trim × (distance of LCF from the after perpendicular / LBP); change forward = change of trim − change aft.
    • Add sinkage and the trim share to each end to get the final drafts.
    • Check the result against the required trim for propeller immersion, bridge visibility under SOLAS Ch. V, and port draught limits.
    The examiner may follow up with
    • Why do loading computers report LCF and not midships?
    • What is hog and sag in draught surveys?
    How did you do?
  13. 13
    DeeperIS Code 2008 Part A 2.2.1–2.2.4

    State the intact stability criteria of the 2008 IS Code Part A 2.2.

    Model answer points
    • Area under the GZ curve not less than 0.055 m-rad up to 30°.
    • Area not less than 0.09 m-rad up to 40°, or up to the angle of down-flooding if that is less than 40°.
    • Area between 30° and 40° (or 30° and down-flooding) not less than 0.03 m-rad.
    • GZ at least 0.2 m at an angle of heel of 30° or more.
    • Maximum GZ at an angle not less than 25° (alternative criteria allowed with Administration approval).
    • Initial GM0 not less than 0.15 m.
    • All values after free surface correction. Then the ship must also meet the weather criterion of Part A 2.3.
    The examiner may follow up with
    • What is the angle of down-flooding?
    • Which ships follow different criteria?
    How did you do?
  14. 14
    DeeperIS Code 2008 Part A 2.3

    Explain the severe wind and rolling criterion (weather criterion).

    Model answer points
    • The ship is assumed to be heeled by a steady beam wind (heeling lever lw1), then to roll to windward by angle θ1 due to waves, and then be hit by a gust (lever lw2 = 1.5 × lw1).
    • lw1 is calculated with a wind pressure P = 504 Pa (may be reduced for restricted service with Administration approval) acting on the lateral windage area A, at lever Z, divided by displacement.
    • The steady-wind heel angle θ0 should not exceed 16° or 80% of the deck edge immersion angle, whichever is less.
    • Area b (above the gust lever, up to θ2) must be equal to or greater than area a (below the gust lever, from the roll-back angle).
    • θ2 is the least of the down-flooding angle, 50°, or the second intercept of lw2 with the GZ curve.
    The examiner may follow up with
    • Why do container ships often limit on the weather criterion?
    • What changes for timber deck cargo?
    How did you do?
  15. 15
    DeeperIS Code 2008 Part A 2.2

    Walk me through the GZ curve. What can you read from it?

    Model answer points
    • Plot GZ against angle of heel from KN curves corrected for the actual KG (and free surface).
    • Initial slope: a tangent at the origin meets a vertical at 57.3° (1 radian) at a height equal to GM.
    • Maximum GZ and the angle at which it occurs.
    • Angle of deck edge immersion: around the point of contraflexure, where the curve starts to flatten.
    • Range of stability and angle of vanishing stability where GZ returns to zero.
    • Dynamic stability: area under the curve × displacement = work done to heel the ship to that angle.
    • Then compare the areas and values with the IS Code criteria.
    The examiner may follow up with
    • How does increasing freeboard change the curve?
    • How does increasing beam change it?
    How did you do?
  16. 16
    DeeperLoad Line Convention 1966/88; IS Code 2008 Part A

    How do beam and freeboard affect the GZ curve?

    Model answer points
    • More beam: higher BM, so higher KM and GM. The curve is steeper at small angles, but deck edge immerses earlier, so the range may not increase much.
    • More freeboard: deck edge immerses at a larger angle, so the maximum GZ is higher and occurs at a larger angle, and the range of stability is greater. Initial GM changes little.
    • Raising G (higher KG) lowers the whole curve by KG sin θ and reduces the range.
    • This is why reserve buoyancy and weathertight integrity of superstructures matter: closing appliances keep the curve valid to large angles.
    The examiner may follow up with
    • Why must weathertight doors be shut at sea?
    • What is reserve buoyancy?
    How did you do?
  17. 17
    DeeperIS Code 2008 Part B 5 (operational provisions); basic stability principles

    How would you correct an angle of loll? Step by step.

    Model answer points
    • First, confirm it is loll, not list: no off-centre weights, no uneven tanks, ship flops to either side, long roll period.
    • Remove free surface: press up or empty slack tanks where possible, without creating new slack tanks.
    • Lower G by adding weight low down: fill the lowest, smallest, divided double bottom tank on the low side first, then its partner on the high side. Filling the high side first can make the ship flop over violently to the other side.
    • If possible, remove top weight (jettison deck cargo only as a last resort, logged and reported).
    • Never try to correct loll by shifting weight to the high side; it can cause a sudden, dangerous lurch.
    • Keep the crew and the company informed; reduce speed and avoid large course changes until GM is positive.
    The examiner may follow up with
    • Why does adding ballast first make the heel worse briefly?
    • What if all DB tanks are full?
    How did you do?
  18. 18
    DeeperSOLAS Ch. II-1 Reg. 5-1; ship's cargo gear manual

    You are loading a heavy lift with the ship's own crane. What happens to stability?

    Model answer points
    • As soon as the weight leaves the quay, its centre of gravity acts at the crane head (point of suspension), not at its own position.
    • Weight lifted from the quay: treat it as loaded at the derrick head. GG1 = w × (height of head above G) / (Δ + w). Weight already on board: GG1 = w × (vertical distance from its own centre of gravity to the head) / Δ. Either way GM falls the moment the weight is suspended.
    • When the jib is swung outboard, G moves off the centreline and the ship lists: tan θ = GG1 / GM, where GM is the reduced value.
    • Before lifting: calculate the maximum list, press up or empty tanks to remove free surface, ensure enough GM, slack mooring lines correctly, clear the area, and secure gangway and other lifts.
    • Use counter-ballast only if the ship is designed for it and the sequence is planned.
    The examiner may follow up with
    • Why tend the moorings during the lift?
    • What is the effect after the weight is landed in the hold?
    • Why does a free-swinging weight act at the point of suspension?
    How did you do?
  19. 19
    DeeperBasic stability principles; docking plan

    Explain the critical period when a ship enters dry dock.

    Model answer points
    • The ship usually enters with a slight trim by the stern. As water is pumped out, the stern touches the blocks first.
    • From that moment an upthrust P acts at the stern. It rises until the ship sits on the blocks fore and aft. This is the critical period.
    • P = (MCTC × change of trim in cm) / distance of the LCF from the point where the stern touches the blocks (usually taken at the after perpendicular).
    • The upthrust reduces effective GM: virtual loss of GM = P × KM / Δ (or, by the second method, P × KG / (Δ − P)).
    • GM must remain positive until the ship is fully landed, otherwise the ship can fall over on the blocks.
    • So: keep trim small, avoid slack tanks, do not move weights, and give the dock master a stability statement.
    The examiner may follow up with
    • Why is a large stern trim dangerous in dock?
    • What happens to GM when the ship refloats?
    How did you do?
  20. 20
    DeeperSOLAS Ch. II-1 Reg. 5; IS Code 2008 Part B 8 and Annex 1

    How is the lightship KG found? Describe the inclining experiment.

    Model answer points
    • The inclining test finds the lightship GM and so the KG. The lightweight survey checks what is on board (weights to add, deduct, relocate) and the actual displacement.
    • Known weights are shifted transversely across the deck. The angle of heel is measured with pendulums (or U-tubes / electronic inclinometers).
    • GM = (w × d) / (Δ × tan θ), where tan θ = pendulum deflection / pendulum length.
    • KG = KM (from hydrostatics) − GM, then corrected to the lightship condition.
    • Conditions: calm water, minimum free surface, moorings slack, all persons not involved ashore, ship upright.
    • Under SOLAS, passenger ships also get periodic lightweight surveys, and a ship is re-inclined if the lightship changes beyond the limits in the regulation.
    The examiner may follow up with
    • Why are slack tanks avoided during the test?
    • Can a sister ship's inclining be accepted?
    How did you do?
  21. 21
    DeeperIS Code 2008 Part A 1.2 and Part B 5.3; MSC.1/Circ.1228

    What is parametric rolling? How do you recognise and avoid it?

    Model answer points
    • A large roll that builds up in head or following seas because the ship's waterplane, and so its GM, changes as wave crests and troughs pass along the hull.
    • It is most likely when the wave encounter period is about half the natural roll period, and wavelength is close to ship length. Container ships with flared bows and flat sterns are most at risk.
    • Signs: rolling builds in a few cycles with pitching, even with the sea ahead or astern.
    • Action: change course and/or speed to change the encounter period; do not rely on autopilot to hold a dangerous heading.
    • The IS Code warns of parametric resonance, broaching and loss of stability on the wave crest, and refers to IMO guidance to the master on adverse weather.
    The examiner may follow up with
    • What is synchronous rolling?
    • What is the risk of loss of stability on a wave crest?
    How did you do?
  22. 22
    DeeperInternational Grain Code A 7.1, A 3, A 9; SOLAS Ch. VI Part C

    What are the grain stability criteria?

    Model answer points
    • From the International Grain Code A 7.1, after allowing for the heeling moment of grain shift:
    • Angle of heel due to grain shift not more than 12°, or for ships built on or after 1 January 1994 the angle at which the deck edge is immersed, whichever is less.
    • Residual area between heeling arm and righting arm curves, up to the angle of maximum difference, 40°, or the flooding angle (whichever is least), not less than 0.075 m-rad.
    • Initial GM, corrected for free surface, not less than 0.30 m.
    • The ship needs a document of authorization and a grain loading manual. Without one, the optional limits of A 9 apply (grain not more than one third of deadweight, plus other conditions).
    The examiner may follow up with
    • How is the grain heeling moment derived?
    • What is a specially suitable compartment?
    How did you do?
  23. 23
    DeeperIS Code 2008 Part A 3.3 (alternative criteria 3.3.2); Load Line Convention Annex I Regs 41–45

    How do you allow for timber deck cargo in stability?

    Model answer points
    • Timber ships may use the IS Code alternative criteria if the deck cargo is stowed between superstructures and across the full beam (within the allowed rounded gunwale) and secured.
    • Alternative criteria: area up to 40° (or flooding angle) at least 0.08 m-rad, maximum GZ at least 0.25 m, and GM at least 0.1 m at all times during the voyage.
    • The GM must allow for water absorbed by the deck cargo and for ice accretion.
    • For the weather criterion, the 16° steady-wind limit applies but the 80% of deck edge immersion limit may be ignored.
    • Watch for a gradual loss of GM and a lazy roll; correct early by ballasting low tanks.
    The examiner may follow up with
    • What is the timber load line?
    • Why is jettisoning timber deck cargo dangerous?
    How did you do?
  24. 24
    DeeperIS Code 2008 Part A 3.1

    What special criteria apply to passenger ships?

    Model answer points
    • Passenger ships must meet Part A 2.2 and 2.3 of the IS Code.
    • In addition, the heel due to crowding of passengers to one side must not exceed 10°. A minimum mass of 75 kg per passenger is assumed, with centres of gravity 1 m above deck for standing and 0.3 m above the seat for seated passengers.
    • The heel due to turning at service speed must not exceed 10°, using the formula in the Code.
    • Damage stability requirements under SOLAS Chapter II-1 are stricter for passenger ships.
    The examiner may follow up with
    • How many persons per square metre are assumed?
    • Why does a ship heel outward in a turn?
    How did you do?
  25. 25
    DeeperSOLAS Ch. II-1 Part B-1 Regs 6–7; Reg. 19 (damage control information)

    What is damage stability and how does SOLAS deal with it today?

    Model answer points
    • Damage stability is the ship's ability to stay afloat and upright after a compartment is breached.
    • Modern SOLAS Chapter II-1 Part B-1 uses the probabilistic method: the attained subdivision index A must be not less than the required index R.
    • Two methods for flooding calculations: lost buoyancy (displacement stays the same, waterplane is reduced) and added weight (flood water treated as weight).
    • Permeability is the proportion of a space that water can fill; cargo, machinery and accommodation spaces have different values.
    • On board, the master uses the damage control plan and booklet, and keeps watertight doors and openings closed as required.
    The examiner may follow up with
    • What is the margin line?
    • What is the purpose of the damage control plan?
    How did you do?
  26. 26
    DeeperIS Code 2008 Part A 3.1.2

    How does heel occur when a ship turns, and why does it matter?

    Model answer points
    • When the rudder is put over, the ship first heels inward briefly (rudder force acts low), then heels outward as the turn develops (centrifugal force acts at G, resistance acts at the centre of lateral resistance, below G).
    • The outward heel is larger with higher speed, smaller turning radius, higher KG and smaller GM.
    • It matters for ships with small GM, deck cargo, container lashings and passengers. The IS Code limits heel on turning for passenger ships to 10°.
    • Reduce speed before large alterations, especially in heavy weather or with a tender ship.
    The examiner may follow up with
    • What happens if the ship has a negative GM and turns?
    • What is a Williamson turn?
    How did you do?
  27. 27
    DeeperIS Code 2008 Part A 2.3.4; Part B (rolling period tables)

    How do you check GM at sea without the loading computer?

    Model answer points
    • Time several full rolls in calm conditions and take the average natural roll period T.
    • Use the IS Code approximate formula: T = 2 × C × B / √GM, where C depends on B, d and waterline length. Rearranged: GM = (2CB / T)².
    • Many booklets give a simpler "rolling period vs GM" table or a constant for the ship.
    • This only gives an approximate GM, but a large, unexpected increase in roll period is an early warning of falling stability.
    The examiner may follow up with
    • What makes the roll test inaccurate?
    • What would you do if the roll period increases during ice accretion?
    How did you do?
  28. 28
    DeeperIS Code 2008 Part B 6.3

    What allowance is made for ice accretion?

    Model answer points
    • In the IS Code Part B guidance (for fishing vessels and as a reference for others), the icing allowance is 30 kg/m² on exposed weather decks and gangways and 7.5 kg/m² on the projected lateral area of each side above the waterline.
    • Ice is high up, so it raises G and increases windage.
    • Action: remove ice with mallets, steam, hot water; reduce speed and alter course to cut spray; keep freeing ports and scuppers clear; monitor roll period.
    • If the roll period increases noticeably, take immediate action to remove ice and increase stability.
    The examiner may follow up with
    • Which areas are worst for icing?
    • What is the Polar Code's link to icing?
    How did you do?
  29. 29
    DeeperShip stability principles; IS Code 2008 Part A 2.2.4 (GM after free surface)

    Displacement 12,000 t, KG 7.40 m, KM 8.20 m. You load 150 t at Kg 10 m, 6 m to starboard. Work out the list.

    Model answer points
    • New displacement: 12,000 + 150 = 12,150 t.
    • New KG by moments about the keel: (12,000 × 7.40 + 150 × 10) / 12,150 = 7.432 m.
    • GM = KM − KG = 8.20 − 7.432 = 0.768 m (assuming KM unchanged and no free surface).
    • GG1 = w × d / Δ = 150 × 6 / 12,150 = 0.074 m.
    • tan θ = GG1 / GM = 0.0965, so the list is about 5.5° to starboard.
    • Then say how you would correct it (weight or ballast to port) and that you would first check fluid GM: free surface makes the list larger.
    The examiner may follow up with
    • How much ballast would you put in a port wing tank 8 m off the centreline to bring her upright?
    • What changes if a slack tank has an FSM of 1,200 t-m?
    How did you do?
  30. 30
    DeeperShip stability principles (dry-docking); stability booklet

    Your ship enters dry dock trimmed 1.2 m by the stern. MCTC is 180 t-m per cm and the after end of the keel is 70 m from the LCF. What is the upthrust and why does it matter?

    Model answer points
    • Upthrust at the stern: P = MCTC × trim (cm) / distance from LCF = 180 × 120 / 70 = about 309 t.
    • The upthrust acts at the keel and reduces effective GM. Virtual loss of GM = P × KM / Δ (for Δ 12,000 t and KM 8.2 m, about 0.21 m).
    • It is greatest just before the ship settles on the blocks fore and aft: the critical period.
    • So: keep trim small, remove free surface, make sure GM is enough to cover the loss, and do not move weights or shift ballast during the critical period.
    • Give the dock master the stability and tank details before entering.
    The examiner may follow up with
    • Why is a large trim by the stern dangerous here?
    • What would you do if the calculation showed a negative GM at the critical instant?
    How did you do?
  31. 31
    TrapIS Code 2008 Part B 3.1

    Trap: "Free surface effect depends on how much liquid is in the tank." True or false?

    Model answer points
    • False. The free surface moment depends on the shape and breadth of the free surface (the moment of inertia of the liquid surface), and on the liquid's density.
    • A tank 10% full and 90% full with the same surface shape give the same virtual rise of G for small angles.
    • The displacement of the ship (in the formula FSM / Δ) affects the virtual rise, not the volume in the tank.
    • Exceptions: very shallow or nearly full tanks at large angles, where the surface touches the tank top or bottom, behave differently. That is why the IS Code accepts 98% as "nominally full".
    The examiner may follow up with
    • How does a longitudinal bulkhead change FSE?
    • What about a tank with a centreline wash plate?
    How did you do?
  32. 32
    TrapBasic stability principles; SOLAS Ch. II-1 Reg. 19

    Trap: the ship is listed 6° to port and the chief officer wants to pump ballast from port to starboard immediately. Do you agree?

    Model answer points
    • Not until I know the cause. If it is a list (G off centre, GM positive), moving weight to starboard corrects it.
    • If it is loll (negative GM), moving weight to starboard can make the ship flop violently to starboard with a larger angle.
    • Check: tank soundings, cargo distribution, recent bunkers or ballast, free surface, whether the ship rolls about the listed position and whether it flops.
    • Also check for flooding (bilge alarms, soundings of void spaces). An unexplained list may be water ingress.
    • Then correct with the right method and record it.
    The examiner may follow up with
    • How would you recognise flooding as the cause?
    • What do you report to the master?
    How did you do?
  33. 33
    TrapIS Code 2008 Part A 2.1.6; Part B 4

    Trap: "If the loading computer says the condition is OK, stability is fine." What do you say?

    Model answer points
    • The computer is only as good as its input: tank soundings, cargo weights, VCGs, density and lightship data.
    • It is a supplement to the approved stability booklet. It must be approved and tested regularly against the booklet's test conditions.
    • The officer must check that limiting values (GM, shear force, bending moment, torsion, lashing forces on container ships) are within limits and that the actual trim is covered.
    • Draught readings vs computer drafts are a good check: a large difference means an input error.
    The examiner may follow up with
    • How often should the stability instrument be tested?
    • What is the constant in a draught survey?
    How did you do?
  34. 34
    TrapIS Code 2008 Part B 5.3; CSS Code

    Trap: "A large GM is always safer." True?

    Model answer points
    • No. Large GM gives a short, violent roll with high accelerations.
    • Risks: container lashing and cargo securing failures, cargo shift, structural racking, injuries, and damage to deck cargo.
    • The aim is to meet all criteria with a sensible margin, not to maximise GM.
    • On container ships, too much GM increases lashing forces; on bulk carriers in ballast, a very stiff ship rolls hard in a beam swell.
    The examiner may follow up with
    • How can you reduce an excessive GM?
    • What is the effect on the officer's choice of ballast?
    How did you do?
  35. 35
    TrapInternational Convention on Load Lines 1966/88, Art. 12; Annex I Reg. 40

    Trap: the ship is in fresh water and the summer load line is submerged by exactly the FWA. Is she overloaded?

    Model answer points
    • Not if she is at her summer displacement. In fresh water (1.000 t/m³) she may submerge the summer load line by the FWA, because she will rise by the FWA when she reaches sea water.
    • In dock water, use DWA in proportion to the density, not the full FWA.
    • But check the zone and season at the first zone she reaches and fuel/water consumed on the river passage: the allowance for consumption may permit a deeper draught, but never beyond the limits.
    • Overloading is a serious offence under the Load Line Convention and flag law.
    The examiner may follow up with
    • How do you calculate the allowable draught in a river port?
    • What is the penalty for overloading?
    How did you do?
  36. 36
    TrapIS Code 2008 Part A 1.2; MSC.1/Circ.1627

    Trap: "The IS Code criteria guarantee the ship will survive any weather." Comment.

    Model answer points
    • No. The 2008 IS Code criteria are empirical, based mostly on casualty data for conventional ships.
    • They do not directly address dynamic failures such as parametric roll, pure loss of stability on a wave crest, broaching, dead-ship condition or excessive accelerations.
    • IMO issued interim guidelines on second generation intact stability criteria for these, approved in 2020 for trial use.
    • Good seamanship still matters: course and speed in heavy weather, securing cargo, closing openings and keeping a sensible GM.
    The examiner may follow up with
    • Name the five failure modes in the second generation criteria.
    • What does a master do when the ship starts parametric rolling?
    How did you do?
  37. 37
    TrapSOLAS Ch. XII Regs 12–13 (water level detectors, dewatering); SOLAS Ch. II-1 Reg. 19

    Trap: you are a bulk carrier with water entering No. 1 hold after a hatch cover failure. Why is it more dangerous than "one compartment flooding" suggests?

    Model answer points
    • Flooding a forward hold causes large trim by the head and loss of freeboard forward; more water enters through hatch openings and ventilators.
    • The free surface of water and wet cargo, and possible progressive flooding through damaged bulkheads, can lead to rapid loss.
    • On a heavily loaded ship (for example, ore with empty alternate holds), the transverse bulkhead may fail under the weight of water and cargo.
    • Actions: sound the general alarm, reduce speed, alter course to reduce green water on the forecastle, start pumps (bilge/dewatering), check water ingress alarms, prepare LSA, send an urgency or distress message as needed, inform the company.
    The examiner may follow up with
    • At what levels do water ingress alarms sound?
    • What is the purpose of SOLAS Ch. XII?
    How did you do?
  38. 38
    TrapIS Code 2008 Part B 3.1

    Trap: the ship heels when you fill a double bottom tank to the brim. You were told filling tanks low always increases GM. Explain.

    Model answer points
    • Adding weight below G lowers G, which increases GM. But while the tank is filling it has a free surface, which raises G virtually.
    • If the tank is wide (a full-breadth DB tank), the free surface effect during filling can be larger than the gain from lowering G, so GM may fall temporarily.
    • If GM was already near zero or negative, the ship may heel or loll while the tank fills, then improve once the tank is pressed up.
    • That is why you fill divided tanks one at a time and press them up quickly.
    The examiner may follow up with
    • Which tank would you fill first in a loll?
    • What does "pressed up" mean?
    How did you do?

Reading answers is not the same as saying them. Our AI voice examiner asks these out loud, listens to your answer, asks the follow-up and marks you against the rule. Join early access or try the free timed mock oral drill.

Frequently asked questions

What is the minimum GM under the IS Code?

Part A 2.2.4 of the 2008 IS Code requires an initial metacentric height GM0 of at least 0.15 m, after correction for free surface. Grain ships need 0.30 m under the Grain Code, and timber ships using the alternative criteria need at least 0.1 m throughout the voyage.

Is the IS Code mandatory?

Part A of the 2008 IS Code is mandatory through SOLAS Chapter II-1 and the 1988 Load Lines Protocol from 1 July 2010. Part B is recommendatory guidance. Ships of 24 m and over built on or after that date must at least comply with Part A.

What is the difference between list and loll?

A list is caused by G being off the centreline while GM is positive. Loll is caused by a negative initial GM, so the ship heels until the GZ becomes zero at the angle of loll. List is corrected by moving weight; loll by lowering G.

How do I correct an angle of loll?

Confirm it is loll, remove free surface where possible, and lower G by filling divided double bottom tanks, starting with the low side. Remove top weight if possible. Never shift weight to the high side.

Do I need to know stability calculations for the oral?

You need to know the formulas and be able to explain and apply them, but the oral rarely asks for long arithmetic. Chief mate and master examiners may ask you to work out a quick figure such as FWA, list or dry-dock upthrust.

What is free surface correction?

It is the virtual rise of G caused by liquid moving in slack tanks. It equals the free surface moment divided by displacement and must be subtracted from solid GM to give fluid GM.

What are the grain stability criteria?

Under the International Grain Code A 7.1: heel from grain shift not more than 12° (or deck edge immersion if less, for ships built from 1994), residual area at least 0.075 m-rad, and GM at least 0.30 m after free surface correction.

Which stability topics are asked at the 2nd mate oral?

Definitions with sketches, GM and GZ, free surface, list and loll, load line marks, FWA and DWA, and how to use the stability booklet. Expect at least one on-watch scenario such as an unexplained list.

What is the weather criterion?

It is the severe wind and rolling criterion in IS Code Part A 2.3. A steady wind heel must not exceed 16° or 80% of deck edge immersion, and the energy area b must be at least area a under a gust lever 1.5 times the steady wind lever.

What is parametric rolling?

It is a large roll that builds up in head or following seas when the ship's stability changes as waves pass along the hull. It is avoided by changing course or speed to alter the wave encounter period.

Which book is best for stability orals?

Use the 2008 IS Code and Grain Code for numbers, then a standard textbook such as Barrass and Derrett or Pursey for explanations. Relate everything to the stability booklet of a ship you have served on.

Can I practise stability orals online?

Yes. Use our free mock oral drill and the stability MCQ bank. Our AI voice mock examiner, which asks questions out loud and follows up, is in early access and not live yet.

Sources 7 documents

Each number in the text links to the source below. Labels show the type of source; see our editorial policy.

  1. Official IMO Resolution MSC.267(85) – Adoption of the International Code on Intact Stability, 2008 · 4 December 2008
  2. Official IMO Resolution MSC.269(85) – Amendments to SOLAS 1974 (Ch. II-1 Reg. 5-1 and related) · 4 December 2008
  3. Official IMO Resolution MSC.267(85), 2008 IS Code Part A 3.4 and footnote 10 · 4 December 2008
  4. Reported UK P&I Club – IMO regulatory update 2026 · 1 January 2026
  5. Official IMO Resolution MSC.532(107) (adopted 8 June 2023) · 8 June 2023
  6. Reported DNV GL Technical Regulatory News No. 23/2020 – IMO MSC 102 · 1 November 2020
  7. Official IMO Resolution MSC.550(108) (adopted 23 May 2024) · 23 May 2024

Where should you go next?

  • Oral topics14 pages: examiner questions with model answer points, deck and engine
  • Question banks7 pages: free MCQ sets with answers and explanations
  • CoC exam guides16 pages: every oral and written exam, authority by authority
  • Free tools4 pages: mock oral drill, lights trainer, sea-time calculator, practice tests
Exam Prep DeskMaritime exam researchers

We write from the conventions (STCW, COLREG, SOLAS, MARPOL), the authorities' own notices and published syllabi, and cite the source for every fee, rule and date. We are independent and not linked to any maritime administration or test provider. Found an error? It matters at sea: tell us and see how we correct · Disclaimer.

Related guides

AI voice mock oral

Say it out loud before the examiner asks.

Our examiner asks CoC oral questions by rank and function, listens to your answer, asks the follow-up and scores you against the rule. Early access is open for India first.

  • Deck and engine, every rank
  • Answers referenced to the conventions
  • Independent, not linked to any authority
WhatsApp us