On this page
- Key facts
- What do examiners ask about marine boilers at each rank?
- What safety fittings must a marine boiler have?
- What boiler water tests do examiners expect you to know?
- How should you structure a boiler answer in the oral?
- What mistakes do candidates make on boiler questions?
- What boiler emergencies do examiners give you?
- How do you prevent a furnace blowback or an economiser fire?
- How do you handle boiler emergencies step by step?
- What separates a weak boiler answer from a strong one?
- What should you read to revise marine boilers?
- Which other engine topics connect to boilers?
- 35 practice questions
- Frequently asked questions
- Sources
Key facts
- Main rule
- SOLAS Ch. II-1 Reg. 32
- Safety valves
- At least two per boiler[1]
- Level indicators
- Two, one a direct-reading gauge glass[1]
- Automatic trips
- Low water, air supply failure, flame failure[1]
- Fuel flash point
- Not below 60 °C[2]
- Asked in
- MEO Class 4, 2, 1; MCA EOOW, Second and Chief Engineer
- Questions here
- 35, core to trap
- Practice
- Boilers MCQ bank and mock oral drill
Checked 14 November 2026. Fees and rules change: confirm with the authority before you book.
What do examiners ask about marine boilers at each rank?
Examiners use boilers to test whether you can keep a pressure vessel safe: water level, safety valves, firing safety and water treatment. At operational level[3] they want correct watchkeeping actions; at management level[3] they want design reasons, survey rules and how you would manage a casualty.
Boilers sit in the marine engineering function of every engineer certificate[4]. In India they come up in the MEO Class 4 oral, the MEO Class 2 oral and the MEO Class 1 oral. In the UK the MCA engineering oral syllabus covers them for the EOOW oral, the Second Engineer oral and the Chief Engineer oral[5]. The table shows the depth we see expected at each level; it is our reading of the syllabus, not a published marking scheme.
| Exam | What the examiner is checking | Typical questions |
|---|---|---|
| India MEO Class 4 | Safe watchkeeping on an auxiliary and exhaust gas boiler | Gauge glass blowdown, safety valve purpose, flame failure, low water action, boiler water tests |
| India MEO Class 2 | Operation plus defects and maintenance | Safety valve setting and survey, accumulation test, tube failure, refractory, corrosion, water treatment chemistry |
| India MEO Class 1 | Management, survey and casualty handling | Boiler survey cycle, class and flag duties, investigation after a furnace explosion, risk assessment for boiler entry |
| MCA EOOW | Routine, non-routine and contingency actions on watch | Start-up, low water alarm response, soot fire in the exhaust gas economiser |
| MCA Second Engineer | Maintenance planning and fault-finding | Inspection of a boiler internally, hydraulic test, feed system contamination |
| MCA Chief Engineer | Responsibility, statutory compliance, decisions | Whether to sail with a defective safety valve, oil contamination of a boiler, reporting to flag and class |
What safety fittings must a marine boiler have?
A boiler must have at least two safety valves, two independent means of showing water level (one a direct-reading gauge glass), and, if oil-fired and unattended, automatic fuel shut-off with an alarm on low water, air supply failure and flame failure[1]. These come from SOLAS Ch. II-1 Reg. 32; class rules add the details.
Learn the list below by function. Examiners often ask "name the boiler mountings" and then pick one and ask how it works and how you test it. Practise the follow-ups in the boilers MCQ bank before the oral.
| Mounting | Purpose | How you prove it works |
|---|---|---|
| Safety valves (at least two) | Release steam so pressure cannot rise beyond the design limit | Set and sealed by the surveyor; hand easing gear tried; accumulation test on new or modified boilers |
| Gauge glasses / level indicators (at least two) | Show the true water level; one must be direct reading | Blowdown sequence on every watch or as the company instructs |
| Low water level alarm and fuel trip | Stop firing before tubes are uncovered | Test by lowering the level or with the test cock as the maker describes |
| Flame failure (flame eye) trip | Shut fuel if the flame goes out so oil does not pool in the furnace | Cover the flame eye during firing and confirm the trip and alarm |
| Forced draught fan failure trip | Stop firing without combustion air | Simulate fan stop or air pressure switch |
| Main steam stop valve | Isolate boiler from the steam range | Operated during shutdown; screw-down non-return type on many boilers |
| Feed check valve | Let feed water in and stop back-flow | Two valves in series on many designs: screw-down stop plus non-return |
| Blowdown valves (scum and bottom) | Remove dissolved solids and sludge | Used as the water treatment programme directs |
| Pressure gauge | Show steam pressure | Calibrated against a test gauge |
| Salinometer / sampling cock | Take a water sample for testing | Daily or as the treatment supplier instructs |
What boiler water tests do examiners expect you to know?
Expect to name the routine tests (alkalinity, chloride, phosphate, hardness, and the oxygen scavenger reserve such as hydrazine or a substitute) and explain why each matters. Exact limits come from the treatment supplier and the boiler maker, so say "within the supplier's limits" unless you quote the chart used on your ship.
The principle examiners want: chlorides tell you about sea water contamination of the feed; alkalinity protects the steel from acid corrosion; phosphate keeps hardness salts as a soft sludge rather than scale; the oxygen scavenger stops pitting. Oil in the feed system is the other big danger, because a thin film of oil on a heating surface insulates it just like scale and the tube overheats.
| Test | What it controls | If out of range |
|---|---|---|
| Chloride | Sea water ingress (condenser leak, drain contamination) | Find the source, increase blowdown, check the condenser and drains, raise treatment dose |
| Alkalinity (P and M or total) | Acid corrosion of steel | Adjust alkalinity dosing; low alkalinity with high chloride points to sea water leak |
| Phosphate reserve | Scale-forming hardness salts kept in suspension | Dose phosphate; very high phosphate wastes chemical and raises dissolved solids |
| Hardness | Calcium and magnesium salts that form scale | Should be nil with correct phosphate; any hardness means contamination or underdosing |
| Oxygen scavenger reserve | Dissolved oxygen that causes pitting | Increase dose; check the hot well temperature and the deaerating arrangements |
| Total dissolved solids / conductivity | Carry-over and priming risk | Scum and bottom blowdown |
| Oil (visual, hot well) | Insulating film and foaming | Find the leaking heater coil, isolate drains to the observation tank, clean the system |
How should you structure a boiler answer in the oral?
Start with safety, then the physics, then the procedure. For any boiler emergency the first sentence the examiner wants is what you do to stop the danger, usually "stop firing", followed by how you protect people and the plant.
A reliable pattern is: (1) the immediate action, (2) what you check and why, (3) who you inform (chief engineer, bridge if steam affects cargo or propulsion), (4) how you find the cause, (5) what you record and report. Draw a simple sketch if allowed: drum, furnace, tubes, gauge glass connections. Many candidates know the procedure but cannot say why the steam cock is shut before the water cock in a gauge glass blowdown. Practise saying the reason aloud with the mock oral drill.
What mistakes do candidates make on boiler questions?
The most common mistake is feeding water into a boiler when the level has dropped out of sight in the gauge glass. Unless you are sure the level is only just below the glass and the heating surfaces are still covered, you stop firing, shut the feed and let the boiler cool. Cold feed water on an overheated tube or furnace can cause sudden failure.
Other mistakes we see in practice sessions:
- Saying the safety valve is set "by the chief engineer". It is set and sealed in the presence of the surveyor; you may only ease it with the hand gear.
- Forgetting purging. Before every light-up the furnace must be purged with air to clear oil vapour.
- Mixing up priming (water carried over with steam because of high level or sudden steam demand) and foaming (bubbles stabilised by oil or high dissolved solids).
- Quoting one maker's pressure as a rule. Give principles unless you name the boiler.
- Ignoring the exhaust gas economiser. Soot fires in the economiser are a classic fire-fighting and boiler question.
- Treating boiler entry as routine. A boiler drum or furnace is an enclosed space; mention isolation, ventilation, gas testing and a permit, as covered in enclosed space entry.
What boiler emergencies do examiners give you?
Scenario questions test whether you act in the right order. The commonest are low water level, a gauge glass that will not show a level, a flame failure that keeps repeating, a furnace blowback, a burst tube, and an exhaust gas economiser fire. The steps below are the low water drill most examiners want to hear.
- 1Stop firing
If the low water alarm sounds or the level cannot be seen, trip the burner (it should trip automatically) and confirm the fuel valve is shut.
- 2Check the gauge glass
Blow down the gauge glass to prove it is not giving a false reading from a choked cock. Compare with the remote level indicator.
- 3Decide whether the heating surface is uncovered
If the level reappears near the bottom of the glass after blowdown, you may slowly restore feed. If the level is out of sight and you cannot prove the surfaces are covered, do not feed.
- 4Shut steam demand and feed
Close the main steam stop valve to reduce draw-off, shut the feed and let the boiler cool naturally. Do not open safety valves to cool it quickly.
- 5Inform and investigate
Inform the chief engineer. Look for the cause: feed pump failure, feed regulator fault, a stuck feed check valve, a tube leak, an open blowdown valve or a leaking drain.
- 6Inspect before re-firing
If tubes or the furnace may have overheated, the boiler must be inspected (and class informed where damage is suspected) before it is fired again.
- 7Record
Enter times, levels, actions and findings in the engine room log book.
How do you prevent a furnace blowback or an economiser fire?
A blowback (furnace explosion) happens when oil vapour builds up in the furnace and then ignites all at once. You prevent it by purging before every light-up, by never trying to relight from hot brickwork, and by keeping burners clean so oil does not drip. If the flame fails, the burner should trip on the flame eye; you purge before trying again.
An exhaust gas economiser fire starts when soot deposits, wetted with unburnt oil, ignite at low engine load. Prevention is regular soot blowing or water washing as the maker recommends, good combustion in the main engine, and keeping the circulation running. In a fire you keep water circulating if the tubes are intact, stop the main engine when safe, and use the fixed water washing or fire-fighting arrangement. A very hot fire can reach the point where iron itself burns (a hydrogen or iron fire), when adding small amounts of water makes it worse; at that stage large amounts of water or boundary cooling are needed and the decision belongs to the chief engineer and master. Link this to the two-stroke main engine questions on low-load running.
How do you handle boiler emergencies step by step?
Protect people first, then the boiler: shut off fuel, keep water in the boiler if you safely can, and never feed cold water into a boiler that has been run dry. These walk-throughs are the scenarios examiners use most for MEO Class 4 and the MCA EOOW oral.
Walk-through 1: water level disappears from the gauge glass
Symptom. You arrive at the boiler and no water is visible in the gauge glass. The low level alarm may or may not have sounded.
Checks in order.
- Blow down the gauge glass: shut the steam and water cocks, open the drain, then open the water cock (water should rush through) and the steam cock (steam should blow), then shut the drain. This tells you whether the glass is reading true or the cocks are choked.
- If water returns to the glass after blowing through, the level was low but not lost: restore feed and investigate.
- If the level is still not visible, treat the boiler as having lost its water.
Likely cause. Feed pump failure, feed check valve stuck shut, feed control valve fault, a large leak, or a choked gauge glass connection giving a false reading.
Action. If the level is truly lost: shut off the burner (it should already have tripped on low level)[1], do not add feed water, close the steam stop valve, and let the boiler cool slowly. Feeding cold water onto overheated plates or tubes can cause a steam explosion or crack them. Once cool, the boiler must be inspected for overheating damage before it is refilled.
Report. Chief engineer at once; log; class may need to be told if pressure parts were overheated.
Examiner's note: The single answer panels listen for is "do not feed". Candidates who say "start the feed pump at once" fail the question.
Walk-through 2: flame failure trips that keep repeating
Symptom. The burner lights, then trips on flame failure; it happens again on restart.
Checks in order.
- Make sure the purge runs fully before each restart. Never shorten it to save time: unburned fuel in the furnace causes blowbacks.
- Clean and check the flame detector (photocell or UV scanner); soot on the lens is common.
- Check fuel temperature and viscosity at the burner, fuel pressure, the burner tip and swirler.
- Check the air register and forced-draught fan damper; too much air blows the flame off.
- Look for water in the fuel (drain the service tank).
Likely cause. Dirty flame eye, poor atomisation (wrong viscosity, worn tip), water in fuel or wrong air–fuel ratio.
Action. Correct the cause and relight with a full purge. Limit the number of restarts; repeated failed ignition fills the furnace with fuel vapour.
Report. Log each trip.
Examiner's note: The strong answer mentions the purge and the blowback risk before any other step.
Walk-through 3: high chloride in the boiler water
Symptom. The daily boiler water test shows chlorides well above the normal range for the ship; hardness may also show.
Checks in order.
- Repeat the test with fresh reagents to rule out a test error.
- Test the condensate and the hot well (cascade tank): is sea water coming in through a leaking condenser, drain cooler or heating coil?
- Check the fresh water generator output salinity if its water feeds the boiler (see fresh water generator).
Likely cause. A sea water leak into the condensate, or fuel tank heating coil condensate contaminated.
Action. Isolate the source, increase blowdown, dose chemicals as the treatment supplier directs and keep testing. Sea water in a boiler leads to scale and corrosion that can fail tubes.
Report. Chief engineer; water treatment log.
Examiner's note: Panels want the hot well check and the condenser leak test, not just "blow down more".
What separates a weak boiler answer from a strong one?
Strong boiler answers name the hazard and the order of actions. The examples below show the difference.
| Question | Weak answer | Strong answer |
|---|---|---|
| Water not visible in the gauge glass | Start the feed pump. | Blow through the gauge glass first; if water is lost, shut the fuel, do not feed, close the steam stop, cool and inspect. |
| Why purge before lighting? | To clean the furnace. | To remove fuel vapour so it cannot ignite explosively when the igniter fires (blowback). |
| How many safety valves? | One per boiler. | At least two, with one accepted only if overpressure protection is otherwise adequate. |
| Why test boiler water daily? | Company requires it. | To keep alkalinity, phosphate and chloride in range so scale, corrosion and foaming do not damage tubes. |
What should you read to revise marine boilers?
Use one standard textbook for the theory and your own ship's boiler manual for real settings. Good sources:
- Marine Steam Boilers by J.H. Milton and R.M. Leach: the classic text on boiler construction and water treatment.
- Reed's Vol 8 General Engineering Knowledge for Marine Engineers: boilers, mountings and water treatment in exam style.
- Introduction to Marine Engineering by D.A. Taylor: clear short chapters on boilers and feed systems.
- Marine Auxiliary Machinery by H.D. McGeorge: feed systems, condensers and auxiliary boilers.
- SOLAS Ch. II-1 Reg. 32 and 33 for the statutory minimum, plus your class society's boiler rules for surveys.
- Your boiler water treatment supplier's test manual and log sheet.
Then test yourself with the boilers MCQ bank, read why seafarers fail oral exams, and follow the 30-day oral preparation plan. The books for MEO Class 4 post lists more titles.
Oral practice
35 oral questions with model answers
Read the question, answer it out loud as if the examiner is across the table, then open the model answer and mark yourself honestly.
- 1
Name the mountings fitted on an auxiliary boiler and say why each is there.
Model answer points
- Two safety valves to prevent overpressure (SOLAS Ch. II-1 Reg. 32).
- Two independent water level indicators, at least one direct-reading gauge glass.
- Main steam stop valve, feed check valve(s), scum and bottom blowdown valves.
- Pressure gauge, air vent, sampling cock for water tests.
- Automatic controls: low water alarm and trip, flame failure trip, forced draught fan failure trip.
- Explain each in one line: what it protects against.
The examiner may follow up with- Which mounting would you check first after a low water alarm?
How did you do? - 2
Walk me through blowing down a gauge glass.
Model answer points
- Purpose: prove both connections are clear and the reading is true.
- Shut the steam cock and water cock, open the drain: the glass empties.
- Open the water cock: water should blow through the drain, proving the water side clear; shut it.
- Open the steam cock: steam blows through, proving the steam side clear; shut it.
- Close the drain, open the water cock then the steam cock: the level should return quickly and settle.
- A slow or no return means a choked cock; compare with the second indicator and report.
The examiner may follow up with- Why does a choked steam cock give a false high level?
- What protection does the glass have against bursting?
How did you do? - 3
The low water alarm sounds on your auxiliary boiler. What do you do?
Model answer points
- Confirm the burner has tripped; if not, stop firing manually.
- Blow down the gauge glass to check the reading is true.
- If the level shows just below normal and surfaces are covered, restore feed slowly and find the cause.
- If the level is out of sight and you cannot prove surfaces are covered, do not feed: shut feed and steam stop, let it cool.
- Check feed pump, feed regulator, feed check valve, blowdown valves, tube leaks.
- Inform the chief engineer and log the event.
The examiner may follow up with- Why not feed cold water into an overheated boiler?
How did you do? - 4
What safety devices stop the burner of an oil-fired boiler, and how do you test them?
Model answer points
- Low water level trip: test by lowering level or with the test arrangement the maker provides.
- Flame failure (photo-cell flame eye): cover the eye during firing and confirm trip and alarm.
- Forced draught fan or air pressure failure: simulate loss of air.
- Often also: high steam pressure, low fuel temperature or pressure for heavy fuel, high water level on some designs.
- Unattended oil-fired boilers must cut fuel and alarm on low water, air supply failure and flame failure.
- Record each test in the planned maintenance system.
The examiner may follow up with- What if the flame eye lens is dirty?
How did you do? - 5
Why must the furnace be purged before lighting up?
Model answer points
- To blow out oil vapour or gas left from a previous firing or a leaking burner.
- Lighting into a vapour-filled furnace causes a blowback (furnace explosion).
- Purge with the forced draught fan at a high air flow for the time set by the maker.
- Never relight from hot refractory; purge again after any flame failure.
The examiner may follow up with- How does the burner management system enforce the purge?
How did you do? - 6
How do you raise steam from cold on an auxiliary boiler?
Model answer points
- Check water level, open air vent, check fuel system, burner and controls.
- Purge, light on low fire, warm up slowly to limit thermal stress on the furnace and refractory.
- Close the air vent when steam issues freely.
- Watch the level, it rises as water expands; blow down if needed.
- Warm and drain steam lines before opening the main stop valve fully to avoid water hammer.
- Follow the maker's warm-up time.
The examiner may follow up with- What is water hammer and how do you prevent it?
How did you do? - 7
What tests do you carry out on boiler water and what does each tell you?
Model answer points
- Chloride: sea water contamination.
- Alkalinity: protection against acid corrosion.
- Phosphate or scale treatment reserve: keeps hardness salts as sludge.
- Hardness: should be nil with correct treatment.
- Oxygen scavenger reserve: protection against pitting.
- Limits come from the treatment supplier; adjust dosing and blowdown to stay within them.
The examiner may follow up with- Chloride is rising fast. Where do you look?
How did you do? - 8
What is the difference between scum blowdown and bottom blowdown?
Model answer points
- Scum blowdown takes water from just below the surface to remove floating impurities and dissolved solids.
- Bottom blowdown removes sludge from the lowest point.
- Bottom blowdown is normally done at low load or when shut down, so sludge has settled and circulation is not disturbed.
- Discharge overboard respects local rules; never leave a blowdown valve unattended open.
The examiner may follow up with- Why is bottom blowdown not done at full firing?
How did you do? - 9
What is the purpose of the hot well and the observation tank?
Model answer points
- Hot well collects returning condensate and lets air escape; it acts as a feed reserve.
- Drains from fuel oil heaters and tank heating coils go first to an observation tank.
- There you can see oil from a leaking coil before it reaches the boiler.
- Filters (often coke or cloth) in the hot well catch traces of oil.
The examiner may follow up with- You see oil in the observation tank. What next?
How did you do? - 10
Why is it dangerous to have oil in the boiler?
Model answer points
- Oil forms an insulating film on heating surfaces, so the metal overheats.
- Can lead to bagging of furnaces, tube failure and rupture.
- Causes foaming and carry-over into the steam system.
- Action: find the leaking heater coil, isolate it, clean the hot well and filters, and chemically clean the boiler if needed.
The examiner may follow up with- How would you detect a heater coil leak?
How did you do? - 11
Explain priming and foaming and how you deal with each.
Model answer points
- Priming: water carried over with steam because of high level or sudden steam demand.
- Foaming: stable froth from oil or high dissolved solids.
- Cure priming: reduce level, avoid sudden load changes.
- Cure foaming: scum blowdown, find contamination, use an antifoam if supplied.
- Carry-over damages steam users and can cause water hammer.
The examiner may follow up with- What is an antifoam?
How did you do? - 12
What is a composite boiler and why is it used on motor ships?
Model answer points
- A boiler that can be heated by main engine exhaust gas and by an oil burner.
- At sea, exhaust gas makes steam; in port or at low load, the oil burner takes over.
- Saves fuel and space compared with separate units.
- Alternative is a separate exhaust gas economiser circulated from an oil-fired boiler drum.
The examiner may follow up with- What is the risk with the exhaust gas side at low load?
How did you do? - 13
The boiler high water level alarm sounds. What are the dangers and what do you do?
Model answer points
- Danger: priming, so water is carried over with the steam into the steam range.
- Carried-over water causes water hammer that can burst pipes, valves and joints, and damages steam users (turbines, heaters).
- Act: stop or reduce feed (check the feed regulator and feed pump), and blow down the gauge glass to confirm the level is real.
- If the level is really high, use scum or bottom blowdown carefully to bring it to normal, watching the glass all the time.
- Open steam line drains to clear any water; reduce sudden steam demand.
- Find the cause (feed regulator fault, level sensor fault, foaming) and record it.
The examiner may follow up with- What is the difference between priming and foaming?
- Why can a choked steam connection on the gauge glass show a false high level?
How did you do? - 14
How do you test a boiler safety valve on board?
Model answer points
- Setting is done in the presence of the surveyor and sealed.
- On board you may test the easing gear to prove the valve lifts and reseats.
- At survey: valves are set at or below the design pressure under steam; an accumulation test may be required.
- Never gag or overload a safety valve.
- Record the test and the setting on the survey record.
The examiner may follow up with- What is an accumulation test?
How did you do? - 15
Describe the different types of safety valve used on marine boilers.
Model answer points
- Ordinary spring-loaded safety valve: lift limited, so needs a larger area.
- Improved high-lift valve: a waste piston or lip gives more lift.
- Full-lift valve: the disc lifts fully on small overpressure, giving full discharge.
- Full-bore relief valve: pilot-operated, used on high-pressure plant.
- All must discharge the full evaporation of the boiler with limited pressure rise.
The examiner may follow up with- Why does a full-lift valve need less area?
How did you do? - 16
What causes boiler tube failure and how would you know a tube has failed?
Model answer points
- Causes: overheating from low water, scale or oil film; corrosion (oxygen pitting, acid, caustic); erosion; fatigue.
- Signs: rapid fall in water level, feed demand rising, steam or water in the furnace, white plume from the funnel, pressure drop.
- Action: stop firing, keep feeding if level can be held to protect other tubes, reduce pressure, shut down.
- Repair: plug the tube both ends after survey agreement, then hydraulic test.
- Inform class; record in the log.
The examiner may follow up with- How many tubes can be plugged before renewal?
How did you do? - 17
How would you carry out an internal inspection of an auxiliary boiler?
Model answer points
- Shut down, cool slowly, drain, isolate and lock out fuel, steam, feed and blowdown.
- Treat as an enclosed space: ventilate, test oxygen and flammable gas, permit, standby person.
- Look for scale, sludge, oil deposits, pitting, cracks at tube ends and around openings.
- Check internal fittings: feed pipe, scum pan, baffles.
- Fire side: soot, refractory damage, bulging furnace, leaking tubes.
- Close with new joints and hydraulic test as required.
The examiner may follow up with- What gas tests and readings must you have before entry?
How did you do? - 18
Your boiler keeps tripping on flame failure. How do you find the fault?
Model answer points
- Check the flame eye lens for soot or oil; clean it.
- Check atomisation: burner tip worn or choked, fuel temperature (viscosity) and pressure.
- Check air/fuel ratio and fan damper position.
- Check for water in fuel and the condition of the filters.
- Check ignition electrodes and igniter.
- Purge before every relight attempt.
The examiner may follow up with- What could happen if you bridged the flame eye to keep firing?
How did you do? - 19
What is the danger of a soot fire in an exhaust gas economiser and how do you fight it?
Model answer points
- Soot wetted with oil ignites, typically after low-load running.
- Small fire: keep water circulating, stop or slow the main engine when safe, use soot blowers or fixed water washing.
- Large fire: risk of hydrogen and iron fire if tubes run dry and overheat.
- At that stage use large amounts of water or boundary cool; small amounts of water feed the reaction.
- Inform the chief engineer and the bridge; prepare fire-fighting teams.
The examiner may follow up with- How do you prevent it?
How did you do? - 20
How do you prevent scale and corrosion in a boiler?
Model answer points
- Feed with distilled or low-solids water, control contamination.
- Phosphate or polymer treatment to keep hardness as sludge.
- Alkalinity control against acid attack.
- Oxygen scavenger and deaeration against pitting.
- Regular blowdown to limit dissolved solids.
- Lay-up: keep full with treated water or dry with desiccant.
The examiner may follow up with- What is caustic embrittlement?
How did you do? - 21
What is a hydraulic test on a boiler and when is it done?
Model answer points
- Filling the boiler with water and raising pressure above working pressure to prove tightness.
- Done after repairs to pressure parts, after tube plugging or renewal, or at survey if the surveyor asks.
- The test pressure is set by class rules.
- Use water, not air, because water stores little energy.
- Look for leaks and permanent distortion.
The examiner may follow up with- Why is a hydraulic test safer than an air test?
How did you do? - 22
What happens at a boiler survey and how often?
Model answer points
- Boilers are surveyed by class at intervals set in class rules, normally internal examination within the survey cycle.
- Surveyor examines pressure parts, mountings and safety valves; sets and seals safety valves under steam.
- Ship prepares: boiler opened, cleaned, gas-free, records of water tests and repairs ready.
- Chief engineer plans it in the survey status list.
The examiner may follow up with- What records would the surveyor ask for?
How did you do? - 23
How is a water-tube boiler different from a fire-tube boiler, and what does that mean for operation?
Model answer points
- Fire-tube: hot gas inside tubes surrounded by water; large water content, slow to raise steam, tolerant of load change.
- Water-tube: water inside tubes; small water content, quick steaming, higher pressures.
- Water-tube needs tighter water treatment and level control.
- Low water is more critical in water-tube boilers because the reserve is small.
The examiner may follow up with- Why is low water more critical in a water-tube boiler?
How did you do? - 24
Describe the operation of a feed water regulator.
Model answer points
- Keeps drum level steady as steam demand changes.
- Single element: measures level only.
- Two or three element: adds steam flow and feed flow to correct for swell and shrink.
- Faults: choked level legs, stuck valve, failed sensor; result is high or low water alarm.
The examiner may follow up with- Explain swell and shrink.
How did you do? - 25
A furnace blowback has just happened on lighting up. What do you do, and what caused it?
Model answer points
- Shut off fuel at once (burner trip and fuel valve closed); keep the forced draught fan running to purge if it is safe.
- Check for people injured and for fire outside the furnace (casing, air register, uptake); have extinguishers ready and inform the bridge and chief engineer.
- Do not relight. Allow the furnace to be purged and cooled.
- Inspect: refractory, burner, casing, uptakes, explosion doors, flame eye and fuel valves.
- Likely causes: no or short pre-purge, relighting from hot refractory, a leaking or dripping burner or solenoid valve, poor atomisation (cold fuel, worn tip), wrong air/fuel ratio, water in fuel.
- Repair the cause, test the burner management sequence (purge timer, flame eye, fuel valves) and record before firing again.
The examiner may follow up with- How does the burner management system enforce the purge?
- Why does a leaking fuel solenoid valve cause blowbacks?
How did you do? - 26
A burner tip keeps carbonising. What are the likely causes?
Model answer points
- Fuel too cold so viscosity too high, poor atomisation.
- Worn or damaged tip, incorrect size.
- Insufficient air or poor air register setting.
- Fuel dripping after shutdown, no purge of the burner.
- Fuel quality: high asphaltenes or water.
The examiner may follow up with- How do you clean a burner tip?
How did you do? - 27
How do you lay up an auxiliary boiler for a long period?
Model answer points
- Wet lay-up: fill completely with treated water (high alkalinity and oxygen scavenger), close all openings.
- Dry lay-up: drain, dry, put in trays of desiccant, close tightly.
- Check the treatment levels or desiccant at intervals.
- Protect fire side from damp to prevent acid corrosion from soot.
The examiner may follow up with- Which lay-up suits a short stop?
How did you do? - 28
The water in the gauge glass is steady but you suspect it is wrong. How do you check?
Model answer points
- Blow down the gauge glass and watch the return.
- Compare with the second indicator and remote level reading.
- A steady level that does not move with firing or feed suggests a choked connection.
- Act on the lower reading until proved.
The examiner may follow up with- Which reading do you trust until proved?
How did you do? - 29
A tube has failed and the level is dropping fast. Do you keep feeding?
Model answer points
- Stop firing at once.
- If the level can still be seen and held, keep feeding to protect the other tubes while pressure falls.
- If the level is lost and cannot be held, stop feeding and let the boiler cool.
- The trap: candidates say "never feed"; the correct answer depends on whether the heating surfaces are still covered.
- Shut down, inspect, repair with class agreement.
The examiner may follow up with- What if the boiler also supplies cargo heating?
How did you do? - 30
The chief engineer suggests raising the safety valve setting slightly because it lifts too early. Your response?
Model answer points
- No. Safety valve settings are made and sealed in the presence of the surveyor.
- Find why it lifts early: setting drift, spring fault, or real pressure overshoot from the controls.
- If adjustment is needed, arrange a surveyor attendance to reset and seal.
- Report and record; tampering is a serious safety and legal issue.
The examiner may follow up with- Who seals the safety valve?
How did you do? - 31
Can you open a boiler that has just shut down to look inside?
Model answer points
- No. It must be cooled, depressurised, drained and isolated first.
- Confirm zero pressure and open the air vent before breaking any joint.
- Treat the drum as an enclosed space with gas test and permit.
- Opening under residual pressure can scald or kill.
The examiner may follow up with- Why open the air vent before breaking a joint?
How did you do? - 32
Is it safe to fire the boiler with one of the two gauge glasses out of service?
Model answer points
- The rule requires two means of indicating level, so one out of service is a defect.
- Repair it as soon as possible; meanwhile keep a close watch and do not leave the boiler unattended.
- Inform the chief engineer, who decides on continued operation and reporting.
- A remote reading alone is not a direct-reading gauge glass.
The examiner may follow up with- What counts as the second means of indicating level?
How did you do? - 33
High chloride in boiler water, but the condenser has no leak. Where else could sea water come from?
Model answer points
- Leaking drains or heating coils in tanks open to sea water.
- Contaminated distilled water from the fresh water generator (high salinity alarm bypassed).
- Feed from a wrong tank or a cross-connection.
- Check the fresh water generator salinometer and feed tank samples.
The examiner may follow up with- What chloride trend tells you the leak is growing?
How did you do? - 34
The flame eye has failed and the voyage is long. Can you fire the boiler manually?
Model answer points
- Only if the maker and company procedures allow manual firing with constant attendance.
- Never bypass the flame failure trip and leave the boiler unattended.
- Fix or renew the flame eye as a priority; carry spares.
- Inform the chief engineer; record the defect.
The examiner may follow up with- Can you ever bridge the flame eye?
How did you do? - 35
What is the danger when the economiser is bypassed but the main engine runs at full load?
Model answer points
- If the economiser has no water flow while hot gas passes, tubes can overheat and fail.
- A dry-running economiser must be designed for it; otherwise keep circulation.
- Check the maker's instructions before running with no circulation.
- Soot fire risk rises with overheated dry tubes.
The examiner may follow up with- How do you fight an economiser soot fire?
How did you do?
Reading answers is not the same as saying them. Our AI voice examiner asks these out loud, listens to your answer, asks the follow-up and marks you against the rule. Join early access or try the free timed mock oral drill.
Frequently asked questions
How many safety valves must a marine boiler have?
At least two, under SOLAS Ch. II-1 Reg. 32. The Administration may accept one if overpressure protection is otherwise adequate, for example on a small boiler. Each must be able to discharge the full steam output.
Why is the steam cock closed first when blowing down a gauge glass?
Because the sequence tests each connection separately. Closing the steam cock and opening the drain proves the water side is clear; then you reverse to prove the steam side. Doing it in order also stops a rush of steam and water hitting the glass at once.
What causes a boiler furnace blowback?
Unburnt oil vapour collecting in the furnace and igniting suddenly. Common causes are skipping the pre-purge, trying to relight from hot brickwork, a leaking or dripping burner, and poor atomisation. Purging before every light-up is the main defence.
Can you add feed water if the level is out of sight in the gauge glass?
Not unless you are sure the heating surfaces are still covered. If in doubt, stop firing, shut the feed and steam, and let the boiler cool. Feeding cold water onto overheated steel can crack or burst it.
What is the difference between priming and foaming?
Priming is water carried over with steam, usually from a high water level or a sudden steam demand. Foaming is a stable froth on the water surface, usually from oil or high dissolved solids. Both cause carry-over; foaming is cured by blowdown and finding the contamination.
Who sets the boiler safety valves?
They are set under steam in the presence of the class or flag surveyor and then sealed. Ship's staff may test the easing gear but must not change the setting. Any change needs a new setting and survey.
What is an accumulation test?
A test that proves the safety valves can release all the steam the boiler makes. With the main steam stop and feed shut and the burner at full firing, pressure must not rise more than the allowed margin above working pressure. The margin is set by class rules; quote it only if you know your class's figure.
Why does oil in boiler water matter so much?
Oil forms a film on heating surfaces that insulates them like scale, so tubes overheat and can fail. It also causes foaming and carry-over. Heater drains go to an observation tank so oil can be seen before it reaches the hot well.
What tests are done on boiler water daily?
Typically chloride, alkalinity, phosphate (or the chosen scale treatment) and the oxygen scavenger reserve, plus a visual check for oil. The exact tests and limits come from the treatment supplier's programme.
Is a boiler an enclosed space?
Yes. A boiler drum, furnace or economiser casing must be treated as an enclosed space. Isolate and lock out fuel, steam and feed, ventilate, test the atmosphere and work under a permit.
What causes an exhaust gas economiser fire?
Soot deposits wetted with unburnt oil igniting, often after long low-load running of the main engine. Regular soot blowing or water washing and good combustion prevent it.
Do MEO Class 4 candidates get asked boiler water chemistry?
Yes, at a practical level: which tests you do, what a high chloride means and what you would do. Detailed chemistry and the reasons behind treatment programmes are pushed harder at Class 2 and Class 1.
Sources 5 documents
Each number in the text links to the source below. Labels show the type of source; see our editorial policy.
- Official Isle of Man SD 603/98 Merchant Shipping (Cargo Ship Construction) Regulations 1998, pressure vessels and boilers (transposing SOLAS Ch. II-1 Reg. 32) · 1 January 1998
- Official Cayman Islands Shipping Registry CIGN 10-2023 Rev 01 Off-specification fuels (quoting SOLAS II-2/4.2.1) · 1 January 2023
- Official STCW Code Section A-I/1 (as amended 2010) · 25 June 2010
- Official MSN 1857 (M+F) Amendment 1: UK requirements for engineer officers and engineer operators
- Official MIN 654 (M) Engineering and Electro-technical Officer Oral Exam Syllabus, Amendment 1 (April 2026) · 21 April 2026